Gardner Denver EAH99C Скачать руководство пользователя

Страница: 73 / 76

13-9-663 Page 72

SYMPTOM

POSSIBLE

CAUSE

REMEDY

Oil carryover

Overfilling the reservoir.

Drain excess oil from
system.

Clogged, broken or loose
oil return lines.

Tighten or replace faulty
lines.

3. Ruptured

oil

separator

element.

3. Replace

element.

Loose assembly.

Tighten all fittings and
gaskets.

Foam caused by use of
incorrect oil.

5. Use

Gardner

Denver

AEON 4000 or 9000 SP
lubricating coolant.

6. Inoperative

minimum

pressure valve.

Replace seals in valve.

Operation at elevated
discharge temperatures.

Reduce temperature. See
“High Discharge Air
Temperature”, this
section.

Scavenge line check valve
failure.

Replace check valve.

Water condensate in oil.

Check oil reservoir
temperature and if low,
change thermal mixing
valve element to higher
temperature.

NOTICE

Gardner Denver factory remanufactured replacement compressor airend units
are available from your authorized distributor, on an exchange basis, for all
rotary screw compressor units.

Содержание EAH99C













































































Результаты поиска

Содержание EAH99C

Отзывы:

Похожие инструкции для EAH99C

Бренды по названию

Популярные бренды

Gardner Denver EAH99C, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание EAH99C

Отзывы:

Похожие инструкции для EAH99C

Бренды по названию

Популярные бренды