Gardner Denver EAH99C Скачать руководство пользователя | Manualshive

Страница: 63 / 76

background image

13-9-663 Page 62

Oil Cooler Oil Pressure Differential (Air-Cooled Radiator)

- Check differential across oil system by

measuring oil inlet pressure as described above.

Oil Cooler Oil Pressure Differential (Water-Cooled Heat Exchanger)

– 2 psid to 25 psid (.1 bar to 1.7

bar) (65 psig to 150 psig, 4.5 bar to 10.3 bar receiver pressure) - Check that oil inlet pressure is correct or
measure the differential between drains on the oil cooler shell.

Oil Cooler Temperature Differential (Air-Cooled Radiator)

- The oil temperature differential depends

on the temperature of the air at the oil cooler fan and cleanliness of core faces. As ambient temperatures
and core restrictions increase, the oil cooler outlet temperature will increase. The oil inlet temperature is
approximately the same as air discharge temperature - see the gauge on the instrument panel. The
outlet oil temperature may be checked by installing a tee at the oil filter outlet.

Oil Cooler Temperature Differential (Water-Cooled Heat Exchanger)

- The oil temperature differential

depends on the inlet water temperature and the water flow rate permitted by the water flow control valve
setting. The oil inlet temperature is approximately the same as the air discharge temperature - see the
gauge on the instrument panel. The oil outlet temperature may be checked by installing a tee at the oil
filter outlet.

Oil Cooler Water Pressure Differential (Water-Cooled Heat Exchanger)

- The water pressure

differential through the heat exchanger will depend on the supply pressure, flow rate, cooler tube
cleanliness and outlet pressure. The inlet and outlet water pressure may be checked at the pipe fittings
supplied by the customer.

«
...
61
62
63
64
65
...
»

Содержание EAH99C













































































Отзывы:

Нет отзывов

Похожие инструкции для EAH99C

Бренд: Keiser Страницы: 14

MCH36 Silent Touch

Бренд: Nuvair Страницы: 56

Бренд: Vector Страницы: 12

Бренд: Power Fist Страницы: 12

Бренд: Power Fist Страницы: 52

Бренд: Powermate Страницы: 8

Бренд: Powerex Страницы: 12

Бренд: Coldex Страницы: 7

Бренд: Clas Ohlson Страницы: 12

Бренд: Clas Ohlson Страницы: 24

Бренд: Clas Ohlson Страницы: 40

Бренд: ERVOR Страницы: 42

Бренд: WilTec Страницы: 5

Бренд: California Air Tools Страницы: 15

Бренд: Xtreme Power Страницы: 5

Бренд: CAMPAGNOLA Страницы: 74

Бренд: CAMPAGNOLA Страницы: 76

Бренд: CAMPAGNOLA Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды