Gantner GAT ECO.Side Lock 7010 F/ISO Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 64

background image

GAT ECO.Side Lock 7010 (NW) F/ISO
Installation

22

HB_GAT-ECOSide-Lock7010-FISO--EN_11

www.gantner.com

3.10 Installation in Lockers with Non-Metallic Doors (except glass)

For lockers with non-metallic doors, the GAT ECO.Side Lock 7010 F/ISO is mounted on the left or right inner locker
wall depending on whether it is a right or left-hinged locker door. The GAT NET.Lock Bolt Set 7100 is mounted on the
inside of the locker door. A drill hole is required in the locker door for the status LED. See the diagram below and the
following installation instructions.

For glass door installation instructions see “3.12. Installation in Lockers with Glass Doors”.

1.  GAT ECO.Side Lock 7010 F/ISO
2.  GAT NET.Lock Bolt Set 7100
3.  3 x mounting holes for the GAT ECO.Side Lock 7010 F/ISO (the use of threaded sleeves is recommended)
5.  Door contact
6.  3 x mounting screws for the GAT NET.Lock BoltSet 7100
7.  Hole for LED

Figure 3.9 - Installation in a locker with non-metallic, right-hinged door (dimensions in mm

– inches shown in brackets)

«
...
20
21
22
23
24
...
»

Содержание GAT ECO.Side Lock 7010 F/ISO

































































Отзывы:

Нет отзывов

Похожие инструкции для GAT ECO.Side Lock 7010 F/ISO

Бренд: Kaba Страницы: 4

Бренд: ASPiSYS Страницы: 3

Бренд: Rollock Страницы: 6

Keypad EZ Remote Unlock

Бренд: BEST ACCESS SYSTEMS Страницы: 2

Бренд: MIWA LOCK Страницы: 4

Smart Keybox v1.0

Бренд: Igloohome Страницы: 9

Бренд: Locinox Страницы: 2

Бренд: NCR Страницы: 29

MUTO Elock MEM4400

Бренд: Dormakaba Страницы: 9

Code Cylinder 1101

Бренд: MYLOQ Страницы: 8

Бренд: Yale Lift-Tech Страницы: 24

YRCB-490-BLE-WSP

Бренд: Yale Страницы: 12

La Gard MECHANICAL

Бренд: Kaba Страницы: 2

Бренд: Kaba Страницы: 2

Generation E-760 AUTO DEADBOLT ASM Office

Бренд: Kaba Страницы: 2

Бренд: Kaba Страницы: 20

Бренд: Kaba Страницы: 32

E-Plex 30 Series

Бренд: Kaba Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды