manualshive.com logo in svg

Gantner GAT ECO.Side Lock 7010 F/ISO, Установка, настройка и эксплуатация

Поделиться
Скачать
Gantner GAT ECO.Side Lock 7010 F/ISO Скачать руководство пользователя страница 29

GAT ECO.Side Lock 7010 (NW) F/ISO 
Installation

 

 

www.gantner.com

 

HB_GAT-ECOSide-Lock7010-FISO--EN_11

 

29

 

3.12  Installation in Lockers with Glass Doors 

 

For lockers with glass doors, the  GAT ECO.Side Lock 7010 F/ISO is mounted on the left or right inner locker wall 
depending on whether it is a right or left-hinged locker door. The GAT NET.Lock Bolt Set 7300 (with metal support 
attached) are glued to the inner side of the locker door. Furthermore, a recess in the printing on the locker door or 
door label may be necessary for the status LED. See the diagram below and the following installation instructions.  

 

 

 

 
 

1. 

GAT ECO.Side Lock 7010 F/ISO 

2. 

GAT NET.Lock BoltSet 7300 

3.     3 x mounting screws for the GAT ECO.Side Lock 7010 F/ISO 
5.     Door contact 
7. 

LED position 

12.  Metal  support  for  adhering  the  GAT  NET.Lock  BoltSet  7300  (the  metal  support  is  included  with  the  GAT 

NET.Lock BoltSet 7300 and is delivered attached to the bolt set). 

 

Figure 3.15 - Installation in a locker with glass, right-hinged door (dimensions in mm 

– inches shown in brackets) 

 

 
 
 
 
 
 
 
 
 
 

 
 

Содержание GAT ECO.Side Lock 7010 F/ISO

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды