manualshive.com logo in svg

Galil Motion Control DMC-40x0 Series, Справочник по командам

Поделиться
Скачать
Galil Motion Control DMC-40x0 Series Скачать руководство пользователя страница 202

192 

●

 PT 

DMC-40x0 Command Reference 

PT   

 

 

 

 

 

 

FUNCTION:

  Position Tracking 

DESCRIPTION:

 

The PT command will place the controller in the position tracking mode.  In this mode, the 

controller will allow the user to issue absolute position commands on the fly.  The motion 
profile is trapezoidal with the parameters controlled by acceleration, deceleration, and speed 
(AD, DC, SP).  The absolute position may be specified such that the axes will begin motion, 
continue in the same direction, reverse directions, or decelerate to a stop.  When an axis is in 
the special mode, the ST command, will exit the mode.  The PA command is used to give the 
controller an absolute position target.  Motion commands other than PA are not supported in 
this mode. 

ARGUMENTS:

  PT n,n,n,n,n,n,n,n 

n=0 or 1 where 1  designates the controller is in the special mode. 

n=?  returns the current setting 

USAGE:    DEFAULTS: 

While Moving 

Yes 

Default Value 

0 

In a Program 

Yes 

Default Format 

1.0 

Command Line 

Yes 

 

 

Controller Usage 

ALL

 

RELATED COMMANDS:

 

PA  

Position Absolute 

AC Acceleration 
DC  

Deceleration 

SP  

Speed 

EXAMPLES:

 

#A

 

 

 PT

1,1,1,1 

;

'Enable the position tracking mode for axes X, Y, Z, and W

#LOOP

 

;

'Create label #LOOP in a program.  This small program will 

;

'update the absolute position at 100 Hz.  Note that the 

;

'user must update the variables V1, V2, V3 and V4 from the 

;

'host PC, or another thread operating on the controller. 

 PA

V1,V2,V3,V4 

;

'Command XYZW axes to move to absolute positions.  Motion 

;

'begins when the command is processed.  BG is not required 

;

'to begin motion in this mode.  In this example, it is 

;

'assumed that the user is updating the variables at a 

;

'specified rate.  The controller will update the new 

;

'target position every 10 milliseconds (WT10). 

 WT

10 

;

'Wait 10 milliseconds 

JP

#LOOP

 

;

'Repeat by jumping back to label LOOP 

Special Notes: The AM, and MC trip points are not valid in this mode.  It is recommended to use MF and 
MR as trip points with this command, as they allow the user to specify both the absolute position, and the 
direction.  The AP trip point may also be used. 

Содержание DMC-40x0 Series

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды