manualshive.com logo in svg

G.T.Power E6D, Руководство по эксплуатации, Страница: 20 / 22

Поделиться
Скачать
G.T.Power E6D Скачать руководство пользователя страница 20

The  output  is  connected  to  a  battery  with  incorrect 
polarity.

This  will  be  displayed  in  case  of  detecting  an 
interruption  of  the  connection  between  battery  and 
output  or  voluntarily  disconnecting  the  charge  lead 
during the operation.

The  cell-count  of  Lithium  battery  pack  was  selected 
incorrectly. Verify the cell-count carefully.

There happens the malfunction at the charger circuit 
by  any  reason.  The  charger  should  be  repaired  at 
the factory.

There  is  a  short-circuit  at  output.  Please  check  the 
charging leads or output cable of battery pack.

The  charger  detects  the  voltage  is  lower  than  you 
set  at  Lithium  program.  Please  check  the  cell-count 
of the battery pack.

The  charge  detects  the  voltage  is  higher  than  you 
set  at  Lithium  program.  Please  check  the  cell-count 
of the battery pack.

The  balancing  circuit  had  been  damaged.  The 
balance  function  can  not  be  used,  and  the  charger 
needs to be repaired at our factory.

The  voltage  of  one  of  the  cell  in  the  Lithium  battery 
pack  is  too  low.  Please  check  the  voltage  of  cells 
one by one.

The  voltage  of  one  of  the  cell  in  the  Lithium  battery 
pack  is  too  high.  Please  check  the  voltage  of  cells 
one by one.

There  are  bad  connection  at  the  individual 
connector.  Please  check  the  connector  and  cables 
carefully.

The  charger  cannot  read  out  the  individual  voltage 
correctly  because  of  malfunction  of  main  processor. 
The charger needs to be repaired.

The voltage of input power drops below the limit.

Check connection ---
Reversed polarity

STOP/ESC

STOP/ESC

Check connection ---
Connection break

Check cell-count ---
Incorrect cell-count 

Check charger ---
Break-down

Check connection ---
Short-circuit

Check battery ---
Low voltage

Check battery ---
High voltage

Check balancer ---
Comm. Error

Balance error ---
Low cell vol.

Balance error ---
High cell vol.

Balance error ---
Bad connection

Balance error ---
Ref. Data fail

Check power ---
Low input volt

Manual of the charger E6D

18

Содержание E6D























Отзывы:

Нет отзывов