Fujitsu PrintPartner 16V Скачать руководство пользователя страница 132

Страница: 132 / 156

Printer Status Indications

Printer Status

Indications

Printer statuses refer to conditions which generally require no action
by you. The following table lists the printer statuses and explains
their meaning. It does not include messages in menu mode.

Message

FORM FEED

<<<INITIALIZE>>>

MENU RESET

PRINT FONT

READY
RESET

SELF TEST

WARMING UP

Meaning

The printer displays this message when you
press with the DATA indicator
off. The printer is printing data remaining
in buffer.

The printer is initializing. This message

appears whenever you turn on the printer,
close the upper door, or lock the paper
guide.

The printer displays this message when you
press for five or more seconds.
This reset returns parameter settings in the

menu to their factory defaults except for
interface settings as well as clears error
latches, buffered data, and temporary soft
fonts.

The printer displays this message when you
press for five or more seconds

then press The printer is printing
the font report.

The printer is ready to print.

The printer displays this message when you

press for five or more seconds. This
reset clears error latches, buffered data, and
temporary soft fonts.

The printer displays this message when you
press five or more seconds

then press The printer is printing
the status report.

The printer is warming up to its operating

temperature.

User’s Manual

5-17

Содержание PrintPartner 16V





























































































































































Результаты поиска

Содержание PrintPartner 16V

Отзывы:

Похожие инструкции для PrintPartner 16V

Бренды по названию

Популярные бренды

Fujitsu PrintPartner 16V, Руководство пользователя

Результаты поиска

Содержание PrintPartner 16V

Отзывы:

Похожие инструкции для PrintPartner 16V

Бренды по названию

Популярные бренды