Fujitsu PRIMERGY RX220 Скачать руководство пользователя страница 60

Страница: 60 / 87

Operating Manual

RX220

Floppy Disk Cannot be Read and/or Written

Troubleshooting and Tips

Mouse controller disabled

The mouse controller on the system board must be enabled if you use the
supplied mouse.

Make sure in the

BIOS Setup

Advanced

menu that the mouse controller is

Enabled

7.7

Floppy Disk Cannot be Read and/or Written

Check whether the write protection for the floppy disk is activated.

Check the entry for the floppy disk drive in the

BIOS Setup Main

menu.

Check in the

BIOS Setup Advanced menu

whether the floppy disk drive

controller is

Enabled

Check in the

BIOS Setup Security menu

whether the floppy disk drive write

permission is

Enabled

. See

“Protecting BIOS from overwriting” on page 55

7.8

Incorrect Time and/or Date

Set the time and/or date in the operating system or in the

BIOS Setup Main

menu.

If the time and date are repeatedly wrong when you switch on your
server, you must change the lithium battery. Contact our Service group.

7.9

System Will Not Boot

The system will not boot after installing a new hard disk drive.

Incorrect SATA configuration (SATA Controller)

In the SATA configuration menu, check the settings for the hard disk drives.

Содержание PRIMERGY RX220
























































































Результаты поиска

Содержание PRIMERGY RX220

Отзывы:

Fujitsu PRIMERGY RX220, Руководство по эксплуатации, Страница: 60 / 87

Результаты поиска

Содержание PRIMERGY RX220

Отзывы: