Fujitsu PRIMERGY RX220 Скачать руководство пользователя страница 47

Страница: 47 / 87

RX220

Operating Manual

Preparation for Use and Operation

Operating and Indicator Elements

5.1.2

The Rear

Figure 11: Connection panel: indicators

LAN activity indicator (green)

Flashes green when a LAN transfer occurs.

Does not light if there is no LAN connection available.

Lights if there is a LAN connection available.

LAN transfer rate indicator (dual color)

No function. Does not light.

Global Error indicator (amber)

Does not light when the system is ok. No service incident or critical event
has occurred.

Flashes amber when a critical event has occurred. Users can check

BIOS Setup

, system event log or via

ServerView

for event details. The

indicator also flashes in standby mode.

Lights amber when a prefailure event has been recognized. Users can
check system event log or via

ServerView

for event details. The indicator

also lights in standby mode.

If the event is still acute after a power failure, the indicator is activated
after the restart.

Table 4: Indicators on the rear

2 3 4

Содержание PRIMERGY RX220
























































































Результаты поиска

Содержание PRIMERGY RX220

Отзывы:

Fujitsu PRIMERGY RX220, Руководство по эксплуатации, Страница: 47 / 87

Результаты поиска

Содержание PRIMERGY RX220

Отзывы: