Fujitsu PRIMERGY RX220 Скачать руководство пользователя страница 52

Страница: 52 / 87

Operating Manual

RX220

Configuring the Server

Perparation for Use and Operation

5.3.2

Configuration with ServerStart

With the

ServerStart

-CD provided, you can configure the server and install the

operating system in a convenient manner. The menu-guided configuration
includes the server configuration using

SCU

and the RAID controller configu-

ration using

GAM

(Global Array Manager).

To find out how to operate

ServerStart

and for further information, refer to the

corresponding ServerStart manual (see

“Related Publications” on page 75

If you use

ServerStart

, you can skip the following sections on how to configure

the server and install the operating system. Continue with

section “Cleaning the

Server” on page 53

5.3.3

Configuration without ServerStart

Configuring the RAID controller

–

The onboard SATA RAID Controller is configured as described in section

“Configuring the SATA RAID controller” on page 51

–

An optional PCI RAID controller is configured as described in the pertaining
documentation.

Installing the Operating System

Insert the installation floppy disk and the CD for the operating system you
want to install into the corresponding drive.

Reboot the server.

Follow the instructions on the screen and in the manual for the operating
system.

Please read how to install the desired operating system in the related
manual for the RAID controller.

Содержание PRIMERGY RX220
























































































Результаты поиска

Содержание PRIMERGY RX220

Отзывы:

Fujitsu PRIMERGY RX220, Руководство по эксплуатации, Страница: 52 / 87

Результаты поиска

Содержание PRIMERGY RX220

Отзывы: