manualshive.com logo in svg

Fujitsu MHT2040BH, Руководство по эксплуатации продукта

Жесткий диск Fujitsu MHT2040BH - это надежное устройство для хранения данных. Для получения подробной информации о продукте обязательно загрузите бесплатное руководство по эксплуатации с manualshive.com. Будьте уверены, что вы владеете всеми функциями этого устройства.

Поделиться
Скачать
background image

 

5.3   Host Commands 

C141-E203-01EN 5-131 

(48)  WRITE LOG EXT (X'3F') 

The WRITE LOG EXTEND command writes versatile log data.  Versatile log data 
includes the Extended SMART Comprehensive Error log, the Extended SMART 
Self-test log, and the SMART Selective log; and each log can be partially written 
with this command.  The effectiveness of the log types depends on customization.  
For the protocol concerning data transfers, see Section 5.4. 

The number of a log to be written is specified as the Log address.  For log data 
consisting of multiple sectors, a sector offset can be specified as an instruction so 
that data transfer starts from the specified sector.  The number of sectors to be 
transferred is specified as the Sector count. 

If this command is not supported, or if an invalid value is specified for the Log 
address, Sector count, or Sector offset, the Aborted Command error occurs. 

• 

Error reporting conditions 

(1)  An error was detected during power-on processing (ST = 51h, ER = 04h). 

(2)  An error was detected during wake-up processing (in cases where wake-up 

processing is required before execution of this command) (ST = 51h, ER = 04h). 

(3)   A write fault was detected while the write cache was disabled  

(ST = 71h, ER = 10h). 

(4)  While the write cache is enabled, if the status indicating a completed transfer 

(STS = 50h) is returned and a data write operation failed because a write fault 
was detected during the data write operation, Abort will be returned for all 
subsequent ATA commands (ST = 71h, ER = 04h).  This state is cleared the 
next time that the device is turned on. 

(5)  An invalid log sector address or invalid Sector count (number of sectors to be 

transferred) is specified (ST = 51h, ER = 04h). 

(6)  The failure prediction capability is disabled (ST = 51h, ER = 04h). 

(7)  A check sum error was detected in the data transferred (ST = 51h, ER = 04h). 

(8)  A SATA communication error occurred (ST = 51h, ER = 0Ch). 

Содержание MHT2040BH









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHT2040BH

Ratoc Systems RS232C User Manual preview
RS232C
Бренд: Ratoc Systems Страницы: 36
Navigloo 3500 Assembly Instructions preview
3500
Бренд: Navigloo Страницы: 3
Hama FlashPen "Piko" Operating Instructions Manual preview
FlashPen "Piko"
Бренд: Hama Страницы: 8
Hama Tenus FlashPen USB 3.0 Operating Instruction preview
Tenus FlashPen USB 3.0
Бренд: Hama Страницы: 4
Seagate Terascale ST4000NC000 Product Manual preview
Terascale ST4000NC000
Бренд: Seagate Страницы: 37
SanDisk Cruizer Enterprise Product Specifications preview
Cruizer Enterprise
Бренд: SanDisk Страницы: 10
G&T SALES Quick Framer Gambrel Roof Instructions preview
Quick Framer Gambrel Roof
Бренд: G&T SALES Страницы: 5
Homak BK02056071 Owner'S Manual & Operating Instructions preview
BK02056071
Бренд: Homak Страницы: 3
kincrome K8114 Manual preview
K8114
Бренд: kincrome Страницы: 2
LaCie 12big Rack Spare Quick Install Manual preview
12big Rack Spare
Бренд: LaCie Страницы: 4
Hama Paletto 00108043 Operating Instruction preview
Paletto 00108043
Бренд: Hama Страницы: 4
SanDisk CruzerSync Getting Started Manual preview
CruzerSync
Бренд: SanDisk Страницы: 7
Impediment RS-1600-X24 User Manual preview
RS-1600-X24
Бренд: Impediment Страницы: 256
ABSCO SHEDS 30082SECOK Manual preview
30082SECOK
Бренд: ABSCO SHEDS Страницы: 23
Buffalo HD-HCU2 DriveStation User Manual preview
HD-HCU2 DriveStation
Бренд: Buffalo Страницы: 8
Quantum RDX 8000 Quick Start Manual preview
RDX 8000
Бренд: Quantum Страницы: 45
Synology DS1621xs+ Hardware Installation Manual preview
DS1621xs+
Бренд: Synology Страницы: 28
TRENDnet TS-U100 - NAS Server - USB User Manual preview
TS-U100 - NAS Server - USB
Бренд: TRENDnet Страницы: 47

Бренды по названию

Популярные бренды

Загрузить еще бренды