Fujitsu MHT2040BH Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 264

background image

5.3 Host Commands

C141-E203-01EN 5-53

Table 5.9 Features Field values (subcommands) and functions (3/3)

Features Field

Function

X’DA’

SMART RETURN STATUS:

When the device receives this subcommand, it saves the current device attribute
values. Then the device compares the device attribute values with guarantee
failure threshold values. If there is an attribute value exceeding the threshold,
F4h and 2Ch are loaded into the Cylinder Low and Cylinder High field. If there
are no attribute values exceeding the thresholds, 4Fh and C2h are loaded into the
Cylinder Low and Cylinder High field. After the settings for the Cylinder Low
and Cylinder High field have been determined, the device transfers the RegDH.

X’DB’

SMART ENABLE/DISABLE AUTO OFF-LINE:

This sets automatic off-line data collection in the enabled (when the Sector
Count field specification

≠

00h) or disabled (when the Sector Count field

specification = 00) state. This setting is preserved whether the drive’s
power is switched on or off.
If 24 hours have passed since the power was switched on, or since the last
time that off-line data were collected, off-line data collection is performed
without relation to any command from the host computer.

The host must regularly issue the SMART READ DATA subcommand (Features
field = D0h), SMART SAVE ATTRIBUTE VALUES subcommand (Features field
= D3h), or SMART RETURN STATUS subcommand (Features field = DAh) to
save the device attribute value data on a medium.

Alternative, the device must issue the SMART ENABLE-DISABLE ATTRIBUTE
AUTOSAVE subcommand (Features field = D2h) to use a feature which regularly
save the device attribute value data to a medium.

The host can predict failures in the device by periodically issuing the SMART
RETURN STATUS subcommand (Features field = DAh) to reference the Cylinder
Low and Cylinder High field.

If an attribute value is below the guarantee failure threshold value, the device is
about to fail or the device is nearing the end of its life. In this case, the host
recommends that the user quickly backs up the data.

«
...
125
126
127
128
129
...
»

Содержание MHT2040BH









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHT2040BH

Бренд: Palram Страницы: 123

Бренд: DANE-ELEC Страницы: 2

SO READY SECURE

Бренд: DANE-ELEC Страницы: 2

Бренд: Quantum Страницы: 88

Бренд: Keter Страницы: 2

My Book World Edition WDH1NC10000

Бренд: Western Digital Страницы: 2

Бренд: Eminent Страницы: 112

IC25N040ATCS04 - Travelstar 40 GB Hard Drive

Бренд: IBM Страницы: 217

Бренд: Excel Страницы: 2

TUSCANY TERRACE 100.1P

Бренд: garofalo Страницы: 16

Бренд: PINIE Страницы: 8

Бренд: Synology Страницы: 31

Бренд: Cavalry Страницы: 16

Бренд: Roth Страницы: 37

Бренд: Costway Страницы: 3

Бренд: Karibu Страницы: 39

Бренд: MSW Motor Technics Страницы: 44

Бренд: Zappiti Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды