Fujitsu MHT2040BH Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 264

background image

Device Overview

1-2 C141-E203-01EN

1.1 Features

1.1.1 Functions and performance

The following features of the disk drive is described.

(1) Compact

The disk drive has 1 disk or 2 disks of 65 mm (2.5 inches) diameter, and its height
is 9.5 mm (0.374 inch).

(2) Large capacity

The disk drive can record up to 40 GB (formatted) on one disk using the RLL
recording method and 30 recording zone technology. The disk drive has a
formatted capacity of 80 GB (MHT2080BH), 60 GB (MHT2060BH), 40 GB
(MHT2040BH) respectively.

(3) High-speed Transfer rate

The disk drive (the MHT Series) has an internal data rate up to 53.9 MB/s.
The disk drive supports an external data rate up to 1.5Gbps (Serial-ATA
Generation-1).

(4) Average positioning time

Use of a rotary voice coil motor in the head positioning mechanism greatly
increases the positioning speed. The average positioning time is 12 ms (at read).

1.1.2 Adaptability

(1) Power save mode

The disk drive is ideal for applications since it supports the power save mode
function that works in each of the Idle, Standby and Sleep modes and has the
Partial and Slumber interface power management functions.

(2) Wide temperature range

The disk drive can be used over a wide temperature range (5 °C to 55 °C).

(3) Low noise and vibration

In Ready status (while the device is waiting for any commands), the Sound Power level
of the disk drives in idle mode is 2.2 Bels [MHT2040BH]/2.8 Bels [MHT2080BH,
MHT2060BH]. The Sound Pressure level is 25.0 dB [MHT2040BH]/34.0 dB
[MHT2080BH, MHT2060BH] as measured 0.3 m from the drive in Idle mode.

(4) High resistance against shock

The Load/Unload mechanism is highly resistant against non-operation shock up
to 8820 m/s

2

(900G).

«
...
22
23
24
25
26
...
»

Содержание MHT2040BH









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHT2040BH

Бренд: IAC INDUSTRIES Страницы: 9

XCubeNAS XN7012R

Бренд: Qsan Страницы: 16

Бренд: Seagate Страницы: 21

Бренд: Data General Страницы: 91

Бренд: Palmako Страницы: 62

Бренд: Yardmaster Страницы: 23

AP-SRFD255AXXXXR-G

Бренд: Apacer Technology Страницы: 18

Бренд: Medion Страницы: 37

Бренд: NCR Страницы: 10

Бренд: Et Страницы: 22

Бренд: Schaffner Страницы: 4

NetShare GX ME-752GNS

Бренд: welland Страницы: 3

Бренд: Acard Страницы: 35

Бренд: CalDigit Страницы: 16

Бренд: Yardmaster Страницы: 24

Бренд: Seagate Страницы: 2

ELECTRONICS DISC DRIVE

Бренд: Watford Страницы: 3

Pro 2-Disk RAID USB and eSATA

Бренд: Verbatim Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды