manualshive.com logo in svg

Fujitsu MHT2040BH, Руководство по эксплуатации продукта

Жесткий диск Fujitsu MHT2040BH - это надежное устройство для хранения данных. Для получения подробной информации о продукте обязательно загрузите бесплатное руководство по эксплуатации с manualshive.com. Будьте уверены, что вы владеете всеми функциями этого устройства.

Поделиться
Скачать
background image

 

Index 

C141-E203-01EN IN-3 

DEVICE CONFIGURATION 

IDENTIFY data structure .................... 5-70 

DEVICE CONFIGURATION 

RESTORE............................................ 5-68 

DEVICE CONFIGURATION SET ........ 5-69 
device connector........................................ 3-9 
device control field.................................. 5-21 
device operation, theory of ........................ 4-1 
device overview......................................... 1-1 
device ready (DRDY) bit......................... 5-20 
device seek complete (DSC) bit .............. 5-20 
device specification ................................... 1-4 
device write fault (DF) bit ....................... 5-20 
device/head field...................................... 5-19 
Device-initiated interface power 

management......................................... 1-14 

Device-nitiated power management 

interface ............................................... 1-14 

diagnosis.................................................... 6-2 
diagnosis, self ............................................ 1-3 
diagnostic code ...............................5-17, 5-39 
digital PLL circuit ................................... 4-11 
dimension .................................................. 3-2 
DIPM ....................................................... 1-14 
disk .....................................................2-2, 4-2 
disk drive outerview .................................. 2-2 
disk enclosure ............................................ 2-2 
dissipation, power...................................... 1-7 
DMA active - device to host.................... 5-13 
DMA buffer offset field........................... 5-21 
DMA data-in command protocol........... 5-146 
DMA data-out command protocol......... 5-147 
DMA setup - device to host or host 

to device (bidirectional) ....................... 5-14 

DMA transfer count field ........................ 5-21 
DOWNLOAD MICROCODE................. 5-41 
DOWNLOAD MICROCODE 

operation .............................................. 5-41 

drive connection ........................................ 2-3 
drive error logging capability .................. 5-59 
drive system configuration ........................ 2-3 
driver circuit ............................................ 4-13 
driver circuit, spindle motor ...................... 4-3 

E

 

E_status field ........................................... 5-21 
ECC, for error correction........................... 1-3 
ECC, for retry ............................................ 1-3 

effect, blower .............................................2-2 
electrical specification ...............................5-6 
enabling and disabling .............................6-19 
ENDEC ....................................................4-11 
environmental specification .......................1-8 
error 

positioning............................................1-11 
unrecoverable read ...............................1-11 

error (ERR) bit .........................................5-20 
error correction by ECC.............................1-3 
error data structure ...................................5-62 
error field .................................................5-17 
error logging capability............................5-59 
error posting...........................................5-139 
error rate...................................................1-11 
EXECUTE DEVICE 

DIAGNOSTIC .....................................5-39 

execution example of READ 

MULTIPLE command .........................5-72 

execution timing of self-calibration ...........4-8 
external force, sensing and 

compensating for....................................4-7 

F

 

failure prediction capability flag..............5-59 
feature ........................................................1-2 
feature flag ...............................................5-66 
features field ............................................5-18 

function ................................................5-51 
value .....................................................5-51 

features field = 

01h......................................................5-114 
02h......................................................5-116 
03h......................................................5-117 
04h......................................................5-118 
C0h .......................................................5-68 
C1h .......................................................5-68 
C2h .......................................................5-69 
C3h .......................................................5-69 

features field value...................................5-97 
filter 

air............................................................4-3 
breather...................................................4-3 
circulation....................................... 2-2, 4-3 

FIR circuit ................................................4-11 
FIS type....................................................5-12 
flag 

failure prediction capability .................5-59 
status.....................................................5-57 

Содержание MHT2040BH









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHT2040BH

IBM 1402 Reference Manual preview
1402
Бренд: IBM Страницы: 80
US Robotics USR8700 User Manual preview
USR8700
Бренд: US Robotics Страницы: 156
Xycom XVME-979 Manual preview
XVME-979
Бренд: Xycom Страницы: 27
USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Owner'S Manual preview
DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116
Бренд: USP Страницы: 79
Quantum DXi V1000 Command Manual preview
DXi V1000
Бренд: Quantum Страницы: 344
IBM Travelstar 10E Installation And Operation Manual preview
Travelstar 10E
Бренд: IBM Страницы: 11
Western Digital WD2503ABYZ Specifications preview
WD2503ABYZ
Бренд: Western Digital Страницы: 2
Gladiator PREMIER GAMT41HWJG Assembly Instructions Manual preview
PREMIER GAMT41HWJG
Бренд: Gladiator Страницы: 24
Freecom DLT-V4 EZ-Kit Series Datasheet preview
DLT-V4 EZ-Kit Series
Бренд: Freecom Страницы: 2
Fantom Drives GD1000EU Specifications preview
GD1000EU
Бренд: Fantom Drives Страницы: 2
Fujitsu HandyDrive-5 Operation Manual preview
HandyDrive-5
Бренд: Fujitsu Страницы: 17
Fujitsu LTO-5 User Manual preview
LTO-5
Бренд: Fujitsu Страницы: 34
Fujitsu MAS3367FC Product/Maintenance Manual preview
MAS3367FC
Бренд: Fujitsu Страницы: 114
Fujitsu MAU3036NC Product/Maintenance Manual preview
MAU3036NC
Бренд: Fujitsu Страницы: 130
Fujitsu GRANPOWER500 TEAMSERVER Series User Manual preview
GRANPOWER500 TEAMSERVER Series
Бренд: Fujitsu Страницы: 14
Fujitsu MAA3182 Product Manual preview
MAA3182
Бренд: Fujitsu Страницы: 142
Fujitsu MAN3367FC - Enterprise 36.7 GB Hard Drive Product/Maintenance Manual preview
MAN3367FC - Enterprise 36.7 GB Hard Drive
Бренд: Fujitsu Страницы: 148
Fujitsu HARD DISK DRIVES MAW3073FC Product/Maintenance Manual preview
HARD DISK DRIVES MAW3073FC
Бренд: Fujitsu Страницы: 112

Бренды по названию

Популярные бренды

Загрузить еще бренды