Fujitsu MHT2040BH Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 264

background image

Interface

5-80 C141-E203-01EN

(24) WRITE DMA (X’CA’ or X’CB’)

The WRITE DMA command writes data to sectors starting from the sectors
specified in the Device/Head, Cylinder High, Cylinder Low, and Sector Number
fields and continuing for as many sectors as specified in the Sector Count field. A
value ranging from 1 to 256 can be specified for the number of the sectors. In
order to specify 256, "00" must be set in the Sector Count field. For the protocol
concerning data transfers, see Section 5.4.5.

When the command is completed, cylinder, head, and sector addresses (CHS
mode) of the last sector to which data was written is stored in the Shadow Block
Register.

If a disk write error is detected during execution of the WRITE DMA command
and continued operation is not possible, command processing is terminated after
all data, including the data of the sector where the error was detected, is
transferred. The device notifies the host of the status by sending the Register DH
FIS. At this time, the number of remaining sectors including the sector where the
error was detected, and either cylinder, head, and sector addresses (CHS mode) or
the logical block address (LBA mode) of the sector where the error was detected
are stored in the Shadow Block Register.

A host system can select the following transfer mode using the SET FEATURES
command, however, the transfer speed does not change.

•

Multiword DMA transfer mode 0 to 2

•

Ultra DMA transfer mode 0 to 5

•

Error reporting conditions

(1) A specified address exceeds the range where write operations are allowed

(after a transfer of dummy data, ST = 51h, ER = 10h).

(2) The range where write operations are allowed will be exceeded by an address

during a write operation (after a transfer of dummy data, ST = 51h, ER = 10h).

(3) A write fault was detected when the write cache was disabled

(ST = 71h, ER = 10h).

(4) While the write cache is enabled, if the status indicating a completed transfer

(STS = 50h) is returned and a data write operation failed because a write fault
was detected during the data write operation, Abort will be returned for all
subsequent ATA commands (ST = 71h, ER = 04h). This state is cleared the
next time that the device is turned on.

(5) A SATA communication error occurred (ST = 51h, ER = 14h).

(6) An error other than the above errors occurred (ST = 51h, ER = 04h).

«
...
152
153
154
155
156
...
»

Содержание MHT2040BH









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHT2040BH

Hawk 1 ST11200N

Бренд: Seagate Страницы: 84

Бренд: Apricorn Страницы: 4

Бренд: G-Technology Страницы: 17

Бренд: Jefferson Страницы: 2

Бренд: Palmako Страницы: 62

SYSTEM STORAGE EXP3000 - INTEROPERABILITY MATRIX...

Бренд: IBM Страницы: 16

Бренд: Macally Страницы: 37

Бренд: IBM Страницы: 2

Бренд: JetStor Страницы: 4

Бренд: AA Products Страницы: 2

Бренд: morse Страницы: 7

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

MSA1GU2 - 1GB Memory Stick Micro M2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды