Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive Скачать руководство пользователя | Manualshive

Страница: 20 / 130

background image

1-4

C141-E185

(8)

Command queuing feature

The IDD can queue maximum 128 commands, and optimizes the issuing order of queued
commands by the reordering function. This feature realizes the high speed processing.

(9)

Reserve and release functions

The IDD can be accessed exclusively in the multi-host or multi-initiator environment by using the
reserve and release functions.

(10)

Error recovery

The IDD can try to recover from errors in SCSI bus or the disk drive using its powerful retry
processing. If a recoverable data check occurs, error-free data can be transferred to the initiator
after being corrected in the data buffer. The initiator software is released from the complicated
error recover processing by these error recovery functions of the IDD.

(11)

Automatic alternate block reassignment

If a defective data block is detected during read or write the IDD can automatically reassign its
alternate data block.

(12)

Programmable data block length

Data can be accessed in fixed-block length units. The data block length is programmable, and can
be specified at initializing with a multiple of four within the range of 512 to 528 bytes.

IMPORTANT

Error rate increase
1. The drive format at factory shipment is generally 512 byte.
2. The Recoverable Error of the drive might increase when the

format would be modified from 512 bytes to the following values:
516 bytes, 520 bytes, 524 bytes, 528 bytes.

3. The Recoverable Error referred to here is sense data (1-13-xx).

(13)

Defective block slipping

A logical data block can be reallocated in a physical sequence by slipping the defective data block
at formatting. This results in high speed contiguous data block processing without a revolution
delay due to defective data block.

(14)

High speed positioning

A rotary voice coil motor achieves fast positioning.

«
...
18
19
20
21
22
...
»

Содержание MAS3184NC - Enterprise 18.4 GB Hard Drive



































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAS3184NC - Enterprise 18.4 GB Hard Drive

Kingston KIS12134

Бренд: Gardiun Страницы: 28

Glasgow KIS12992

Бренд: Gardiun Страницы: 26

Бренд: Edirol Страницы: 1

HAWK 2 ST11900W

Бренд: Seagate Страницы: 40

Бренд: Seagate Страницы: 54

Бренд: U-Line Страницы: 18

Quick Framer Gambrel Roof

Бренд: G&T SALES Страницы: 5

Бренд: Et Страницы: 22

Recessed Mounted Pan Door Medicine Cabinets 935/936

Бренд: NuTone Страницы: 1

MaxAttach NAS 4000

Бренд: Maxtor Страницы: 2

SmartStore SM2020

Бренд: Riverlea Страницы: 16

Бренд: U-Line Страницы: 6

Бренд: Hama Страницы: 5

Бренд: Clarke Страницы: 8

Бренд: ABSCO SHEDS Страницы: 21

MediaLounge DSM-602H

Бренд: D-Link Страницы: 12

SharePort DNS-323

Бренд: D-Link Страницы: 17

Бренд: D-Link Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды