Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive Скачать руководство пользователя

Страница: 104 / 130

6-8

C141-E185

See Section 5.1 for notes on packing and handling when returning the disk drive.

6.2.3Maintenance levels

If a disk drive is faulty, replace the whole disk drive since repair requires special tools and
environment. This section explains the two maintenance levels.

(1)

Field maintenance (disk drive replacement)

•

This replacement is done at the user's site.

•

Replacement uses standard tools.

•

Replacement is usually done by the user, retail dealer, distributor, or OEM engineer.

(2)

Factory maintenance (parts replacement)

•

This replacement can only be done by Fujitsu.

•

Replacement includes maintenance training and OEM engineer support. OEM engineers
usually support retail dealers and distributors.

•

Replacement uses factory tools and test equipment.

Содержание MAS3184NC - Enterprise 18.4 GB Hard Drive



































































































































Результаты поиска

Содержание MAS3184NC - Enterprise 18.4 GB Hard Drive

Отзывы:

Похожие инструкции для MAS3184NC - Enterprise 18.4 GB Hard Drive

Бренды по названию

Популярные бренды

Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive, Руководство по эксплуатации/техническому обслуживанию

Результаты поиска

Содержание MAS3184NC - Enterprise 18.4 GB Hard Drive

Отзывы:

Похожие инструкции для MAS3184NC - Enterprise 18.4 GB Hard Drive

Бренды по названию

Популярные бренды