Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive Скачать руководство пользователя

Страница: 12 / 130

C141-E185

4.3.2

68 pin connector type 16-bit SCSI model (NP model)......................................................4-13

4.3.3

Cable connector requirements ...........................................................................................4-20

4.3.4

External operator panel (on NP model drives only) ..........................................................4-21

CHAPTER 5

INSTALLATION...............................................................................................5-1

5.1

Notes on Handling Drives .................................................................................................5-1

5.2

Connections.......................................................................................................................5-3

5.3

Setting Terminals ..............................................................................................................5-5

5.3.1

SCSI ID setting..................................................................................................................5-6

5.3.2

Each mode setting .............................................................................................................5-8

5.3.3

Mode settings ....................................................................................................................5-10

5.4

Mounting Drives................................................................................................................5-11

5.4.1

Check before mounting .....................................................................................................5-11

5.4.2

Mounting procedures.........................................................................................................5-11

5.5

Connecting Cables.............................................................................................................5-12

5.6

Confirming Operations after Installation and Preparation for

se ....................................5-13

5.6.1

Confirming initial operations.............................................................................................5-13

5.6.2

Checking SCSI connection................................................................................................5-14

5.6.3

Formatting .........................................................................................................................5-17

5.6.4

Setting parameters .............................................................................................................5-19

5.7

Dismounting Drives...........................................................................................................5-23

5.8

Spare Disk Drive ...............................................................................................................5-23

CHAPTER 6

DIAGNOSTICS AND MAINTENANCE ........................................................6-1

6.1

Diagnostics ........................................................................................................................6-1

6.1.1

Self-diagnostics .................................................................................................................6-1

6.1.2

Test programs....................................................................................................................6-4

6.2

Maintenance Information ..................................................................................................6-5

6.2.1

Precautions ........................................................................................................................6-5

6.2.2

Maintenance requirements.................................................................................................6-6

6.2.3

Maintenance levels ............................................................................................................6-8

6.2.4

Revision numbers ..............................................................................................................6-9

6.2.5

Tools and test equipment...................................................................................................6-10

6.2.6

Tests ..................................................................................................................................6-10

6.3

Operation Check................................................................................................................6-12

6.3.1

Initial seek operation check ...............................................................................................6-12

6.3.2

Operation test ....................................................................................................................6-12

Содержание MAS3184NC - Enterprise 18.4 GB Hard Drive



































































































































Результаты поиска

Содержание MAS3184NC - Enterprise 18.4 GB Hard Drive

Отзывы:

Похожие инструкции для MAS3184NC - Enterprise 18.4 GB Hard Drive

Бренды по названию

Популярные бренды

Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive, Руководство по эксплуатации/техническому обслуживанию

Результаты поиска

Содержание MAS3184NC - Enterprise 18.4 GB Hard Drive

Отзывы:

Похожие инструкции для MAS3184NC - Enterprise 18.4 GB Hard Drive

Бренды по названию

Популярные бренды