Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive Скачать руководство пользователя | Manualshive

Страница: 101 / 130

background image

C141-E185

6-5

(1)

Interface (SCSI bus) test

The operations of the SCSI bus and data buffer on the IDD are checked with the WRITE BUFFER
and READ BUFFER commands.

(2)

Basic operation test

The basic operations of the IDD are checked by executing self-diagnosis with the SEND
DIAGNOSTIC command (see Subsection 6.1.1).

(3)

Random/sequential read test

The positioning (seek) operation and read operation are tested in random access and sequential
access modes with the READ, READ EXTENDED, or VERIFY command.

(4)

Write/read test

By using a data block in the internal test space, the write/read test can be executed with an arbitrary
pattern for a disk drive in which user data is stored.

6.2

Maintenance Information

6.2.1

Precautions

Take the following precautions to prevent injury during maintenance and troubleshooting:

CAUTION

1.

To avoid shocks, turn off the power before connecting or disconnecting a
cable, connector, or plug.

2.

To avoid injury, do not touch the mechanical assembly during disk drive
operation.

3.

Do not use solvents to clean the disk drive.

Take the following precautions to prevent disk drive damage during maintenance and
troubleshooting:

«
...
99
100
101
102
103
...
»

Содержание MAS3184NC - Enterprise 18.4 GB Hard Drive



































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAS3184NC - Enterprise 18.4 GB Hard Drive

Бренд: OWC Страницы: 2

Бренд: V-TAC Страницы: 28

MARK V Model 520

Бренд: Shopsmith Страницы: 32

Бренд: Nexsan Страницы: 76

Бренд: Soyntec Страницы: 8

Forensic ComboDock FCDv6

Бренд: WiebeTech Страницы: 20

Бренд: SanDisk Страницы: 7

Бренд: Newpo Страницы: 5

Бренд: Stardom Страницы: 108

Бренд: Infrant Technologies Страницы: 98

PowerProtect X400

Бренд: Dell EMC Страницы: 42

Бренд: Bosch Страницы: 30

Бренд: Bosch Страницы: 68

Бренд: EDSLab Страницы: 24

Backup Exec 3600 R3

Бренд: Symantec Страницы: 22

PlatinumRAID Ultra320

Бренд: MicroNet Страницы: 73

Бренд: Cavalry Страницы: 20

CADA-U32A Series

Бренд: Cavalry Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды