Fujitsu F2MC-8L Series Скачать руководство пользователя страница 62

Страница: 62 / 131

HARDWARE CONFIGURATION

2-42

TIME-BASE TIMER

Description of Registers

The detail of time-base timer control register (TBCR) is described below.

(1) Time-base timer control register (TBCR)

Address: 000A

Initial value

00---000

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

TBOF

TBIE

—

TBC1

TBC0

TBR

(R/W)

(W)

TBCR

[Bit 7] TBOF: Interval timer overflow bit
When writing, this bit is used to clear the interval timer overflow flag.

Interval timer overflow flag cleared

No operation

When reading, this bit indicates that an interval timer overflow has occurred.

Interval timer overflow not occurred

Interval timer overflow occurred

1 is read when the Read Modify Write instruction is read. If the TBIF bit is set
to 1 when the TBIE bit is 1, an interrupt request is output. This bit is cleared
upon reset.

[Bit 6] TBIE: Interval-timer interrupt enable bit
This bit is used to enable an interrupt by the interval timer.

Interval interrupt disabled

Interval interrupt enabled

[Bit 2 and 1] TBC1, TBC2: Interval time specification bit
These bits are used to specify interval timer cycle.

0.26 ms

0.51 ms

1.02 ms

0.524 s

TBC1

TBC0

Interval time

: main clock frequency

8 MHz source clock

[Bit 0] TBR: Time-base timer clear bit
This bit is used to clear time-base timer.

Time-base timer cleared

No operation

1 is always read when this bit is read.

Содержание F2MC-8L Series




































































































































Результаты поиска

Содержание F2MC-8L Series

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu F2MC-8L Series, Руководство по оборудованию

Результаты поиска

Содержание F2MC-8L Series

Отзывы:

Бренды по названию

Популярные бренды