manualshive.com logo in svg

Fujitsu ESPRIMO P, Руководство по эксплуатации

Поделиться
Скачать
Fujitsu ESPRIMO P Скачать руководство пользователя страница 57

 

System upgrades

 

A26361-K1007-Z230-1-7619, edition 1 

49 

Installing an accessible drive 

►

 

Open the casing (see "Opening the casing"). 

►

 

If a slide-in module is fitted, remove this first. To do this, proceed in the same way as when 
removing an accessible drive (see "Removing an accessible drive"). 

 

!

 

Do not dispose of the empty slide-in module. For cooling, protection against fire, and in 
order to comply with EMC regulations, you must refit the empty slide-in module if you 
remove the drive again later. 

 

 

►

 

Adjust the required settings on the drive (if necessary, on already-installed drives as well). 

2

1

 

 

►

 

Slide the accessible drive into the casing as far as the stop (1). 

►

 

Plug the data and the power supply connectors into the drive. Make sure the polarity is correct. 

►

 

Press on the retaining clip (2) and, at the same time, slide it up slightly. 

►

 

Close the casing (see "Closing the casing"). 

 

i

 

It may be necessary to modify the entry for the drive in the 

BIOS Setup

. 

 

Содержание ESPRIMO P







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды