Fujitsu ESPRIMO P Скачать руководство пользователя страница 35

Страница: 35 / 70

A26361-K1007-Z230-1-7619, edition 1

Troubleshooting and tips

Refer to the safety notes in the "Safety" manual and in the "Preparing for use" chapter
when connecting or disconnecting cables.

If a fault occurs, try to correct it as described in the following places:

●

in this chapter

●

in the documentation of the connected devices

●

in the help systems of the software used

●

in the documentation of your operating system

If you fail to correct the problem, proceed as follows:

►

Switch the device off.

►

Make a note of the steps and the circumstances that led to the fault.

►

Make a note of any error messages displayed.

►

Note the ID number of your device. The ID number can be found on the type rating plate on the
back of the casing.

►

Contact your sales outlet or our customer service centre.

Troubleshooting

Power-on indicator remains unlit after you have switched on
your device

Cause

Troubleshooting

The mains voltage supply is faulty.

►

Check whether the power cable is plugged properly
into the device and a grounded mains outlet.

►

Switch the device on.

Internal power supply overloaded.

►

Unplug the mains plug of the device from the mains
socket.

►

Wait for a moment.

►

Plug the power plug into a properly grounded mains
outlet again.

►

Switch the device on.

Содержание ESPRIMO P







































































Результаты поиска

Содержание ESPRIMO P

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu ESPRIMO P, Руководство по эксплуатации

Результаты поиска

Содержание ESPRIMO P

Отзывы:

Бренды по названию

Популярные бренды