Fujitsu ASTG12CMCB, Руководство по установке

Страница: 12 / 16

En-12
(8) Paste protect seals (2 locations) to prevent the wires from sticking out.
(8)
13.3.5. Installing front panel
( See “9.2. Front panel installation” )
14. SELECTING THE REMOTE CONTROLLER CUSTOM CODE
When two or more air conditioners are installed in a room and the remote controller is
operating an air conditioner other than the one you wish to set, change the custom code
of the remote controller to operate only the air conditioner you wish to set (4 selections
possible).
When two or more air conditioners are installed in a room, please contact your retailer to
set the individual air conditioner custom codes.
Selecting the Remote Controller Custom Code
Use the following steps to select the custom code of the remote controller. (Note that the
air conditioner cannot receive a custom code if the air conditioner has not been set for the
custom code.)
(1) Press the START/STOP ( ) button until only the clock
is displayed on the remote controller display.
(2) Press the MODE button for at least 5 seconds to display
the current custom code (initially set to ).
(3) Press the TEMP. ( / ) buttons to change the custom
code between .
Match the code on the display to the air conditioner
custom code.
(4) Press the MODE button again to return to the clock
display. The custom code will be changed.
• If no buttons are pressed within 30 seconds after the custom code is displayed, the
system returns to the original clock display. In this case, start again from step (1).
• The air conditioner custom code is set to A prior to shipment.
15. FUNCTION SETTING
Perform the “FUNCTION SETTING” according to the installation conditions using the remote
controller.
CAUTION
• Con fi rm whether the wiring work for outdoor unit has been fi nished.
• Con fi rm that the cover for the electrical enclosure on the outdoor unit is in place.
• This procedure changes to the function settings used to control the indoor unit according
to the installation conditions. Incorrect settings can cause the indoor unit to malfunction.
• After the power is turned on, perform the “FUNCTION SETTING” according to the
installation conditions using the remote controller.
• The settings may be selected between the following two: Function Number or Setting
Value.
• Settings will not be changed if invalid numbers or setting values are selected.
• Refer to the installation manual enclosed with the remote control unit when the wired
remote control unit (option ) is used.
Entering the Function Setting Mode
While pressing the POWERFUL button and TEMP. ( ) button simultaneously, press the
RESET button to enter the function setting mode.
Selecting the Function Number and Setting Value [Reverse cycle model]
(1) Press the TEMP. ( / ) buttons to select the func-
tion number. (Press the 10°C HEAT button to switch
between the left and right digits.)
(2) Press the POWERFUL button to proceed to setting
value. (Press the POWERFUL button again to return
to the function number selection.)
(3) Press the TEMP. ( / ) buttons to select the setting
value. (Press the 10°C HEAT button to switch between
the left and right digits.)
(4) Press the MODE button once to send the function set-
ting information. Please con
fi rm the beeping sound.
(5) Next, please press START/STOP ( ) button once
to fi x the function setting. Please con fi rm the beeping
sound.
(6) Press the RESET button to cancel the function setting
mode.
(7) After completing the FUNCTION SETTING, be sure to
turn off the power and turn it on again.
Function Number
Setting
Value
Selecting the Function Number and Setting Value [Cool model]
(1) Press the TEMP. ( / ) buttons to select the func-
tion number. (Press the ECONOMY button to switch
between the left and right digits.)
(2) Press the POWERFUL button to proceed to setting
value. (Press the POWERFUL button again to return
to the function number selection.)
(3) Press the TEMP. ( / ) buttons to select the setting
value. (Press the ECONOMY button to switch between
the left and right digits.)
(4) Press the MODE button once to send the function set-
ting information. Please con
fi rm the beeping sound.
(5) Next, please press START/STOP ( ) button once
to fi x the function setting. Please con fi rm the beeping
sound.
(6) Press the RESET button to cancel the function setting
mode.
(7) After completing the FUNCTION SETTING, be sure to
turn off the power and turn it on again.
Function Number
Setting
Value
CAUTION
After turning off the power, wait 30 seconds or more before turning on it again. The
function setting does not become active unless the power is turned off then on again.
15.1.
Function details
Filter Sign
Select appropriate intervals for displaying the fi lter sign on the indoor unit according to the
estimated amount of dust in the air of the room.
If the indication is not required, select “No indication” (03).
( ♦ ... Factory setting)
Function Number
Setting
Value
Setting Description
11
00 Standard (400 hours)
01 Long interval (1000 hours)
02 Short interval (200 hours)
03 No indication ♦
Auto Restart
Enable or disable automatic restart after a power interruption.
( ♦ ... Factory setting)
Function Number
Setting
Value
Setting Description
40
00 Enable ♦
01 Disable
* Auto restart is an emergency function such as for power outage etc. Do not attempt to
use this function in normal operation. Be sure to operate the unit by remote controller or
external device.
9333005201_IM_En_ASTG09KMCA.indd 12 9333005201_IM_En_ASTG09KMCA.indd 12 2017/1/20 11:43:07 2017/1/20 11:43:07