En-9
(5)
(6) Install the cover of the control box onto the inner side of the rib as shown below.
CAUTION
• Do not cut or tuck the wires with the electrical component box cover.
An electric shock may occur if the wires are damaged.
(7) Tighten with screws to prevent the cover of the control box from falling off.
(When installing, reuse the screws that was removed in 13.3.2. Removing control
box.)
(7)
(7)
(6)
(8) Paste protect seals (2 locations) to prevent the wires from sticking out.
(8)
12.3.6. Installing front panel
( Refer to 9.2. Front panel installation )
14. FUNCTION SETTING
Perform the “FUNCTION SETTING” according to the installation conditions using the remote
controller.
CAUTION
• Con
fi
rm whether the wiring work for Outdoor unit has been
fi
nished.
• Con
fi
rm that the cover for the electrical enclosure on the outdoor unit is in place.
• This procedure changes to the function settings used to control the indoor unit according
to the installation conditions. Incorrect settings can cause the indoor unit to malfunction.
• After the power is turned on, perform the “FUNCTION SETTING” according to the
installation conditions using the remote controller.
• The settings may be selected between the following two: Function Number or Setting
Value.
• Settings will not be changed if invalid numbers or setting values are selected.
• Refer to the installation manual enclosed with the remote control unit when the wired
remote control unit (option ) is used.
Entering the Function Setting Mode
While pressing the POWERFUL button and SET TEMP. ( ) simultaneously, press the RESET
button to enter the function setting mode.
STEP 1
Selecting the Remote Controller Custom Code
Use the following steps to select the custom code of the remote
controller. (Note that the air conditioner cannot receive a cus-
tom code if the air conditioner has not been set for the custom
code.)
The custom codes that are set through this process are applica-
ble only to the signals in the FUNCTION SETTING. For details
on how to set the custom codes through the normal process,
refer to Remote controller custom code.
(1)
Press SET TEMP. ( /
) button to change the custom
code between
. Match the code on the dis-
play to the air conditioner custom code. (initially set to )
(If the custom code does not need to be selected, press the
10°C HEAT button and proceed to STEP 2.)
(2)
Press the MODE button and check that the indoor unit can
receive signals at the displayed custom code.
(3)
Press the 10°C HEAT button to accept the custom code,
and proceed to STEP 2.
The air conditioner custom code is set to A prior to shipment. Contact your retailer to
change the custom code.
The remote controller resets to custom code A when the batteries in the remote con-
troller are replaced. If you use a custom code other than custom code A, reset the
custom code after replacing the batteries.
If you do not know the air conditioner custom code setting, try each of the custom
codes (
) until you
fi
nd the code which operates the air conditioner.
STEP 2
Selecting the Function Number and Setting Value
(1)
Press the SET TEMP. ( /
) buttons to select the function number. (Press the 10°C
HEAT button to switch between the left and right dig-
its.)
(2)
Press the POWERFUL button to proceed to setting
value. (Press the POWERFUL button again to return
to the function number selection.)
(3)
Press the SET TEMP. ( /
) buttons to select the
setting value. (Press the 10°C HEAT button to switch
between the left and right digits.)
(4)
Press the MODE button, and START/STOP button, in
the order listed to con
fi
rm the settings.
(5)
Press the RESET button to cancel the function set-
ting mode.
(6)
After completing the FUNCTION SETTING, be sure
to turn off the power and turn it on again.
Function Number
Setting
Value
9333005072_IM.indb 9
9333005072_IM.indb 9
2013-9-24 11:45:13
2013-9-24 11:45:13
Содержание AOYG14LMCBN
Страница 12: ......
