FUJI CONTROLS IN-100 Скачать руководство пользователя страница 56

Страница: 56 / 61

Brightness

What is "Brightness"?

This function allows you to adjust brightness of the backlight of the display.

OFF

turns on the backlight with a standard brightness level for 5 seconds from key

operation. Select brightness levels of either

Dark

Normal

, or

Bright

Only while the backlight is on, key operation is kept effective. While it is off, press an

arbitrary key and start operation.

How to set

1. Press MENU key.

2. Use



⋀



⋁

key to select

System Setting

3. Press SET key.

4. Use



⋀



⋁

key to select

Brightness

5. Press SET key.

6. Use



key to select OFF, Dark, Normal, or Bright. (default: Normal)

7. Press SET key and confirm the cursor has turned green.

8. Press SET key again to complete this operation.

Содержание IN-100






























































Результаты поиска

Содержание IN-100

Отзывы:

Похожие инструкции для IN-100

Бренды по названию

Популярные бренды

FUJI CONTROLS IN-100, Инструкция по эксплуатации

Результаты поиска

Содержание IN-100

Отзывы:

Похожие инструкции для IN-100

Бренды по названию

Популярные бренды