FUJI CONTROLS IN-100 Скачать руководство пользователя страница 4

Страница: 4 / 61

Safety Instructions

This Manual provides precautions and instructions to be complied with by users of this

Product so users may safely and properly use the Product. Use the Product based on

understanding of these instructions.

Warnings

Power supply beyond the rated value to the Product may damage it, cause fire, or cause

electric shock. Be sure to use the Product within the rated specifications.

Use of the Product in an atmosphere where there is a risk of explosion is dangerous.

Avoid using the Product in such conditions, including the following:



Places where there is corrosive gas or flammable gas



Place where the Product is likely to be splashed or dripped on by water, oil

or chemicals

Whenever the Product breaks down (abnormal smell or heat generation), immediately

stop using it and remove the power plug. Otherwise, it may cause a fire or electric shock.

Do not disassemble the Product.

Sufficiently examine the wiring before supplying electric power to the Product.

Be sure to provide Type D grounding during installation.

When a panel or wire is cut, be sure not to let foreign matter such as metal chips inside.

Do not drop or subject the Product to strong impacts. Otherwise, the Product may be

damaged. When that happens, stop using the Product and contact us.

When the Product is used in ways not described by the Manual, safe use may be

compromised. Be sure to use the Product as specified by the Manual.



Be aware of potential risks to users of the Product, including death or

serious injury, associated with the following items.

Содержание IN-100






























































Результаты поиска

Содержание IN-100

Отзывы:

Похожие инструкции для IN-100

Бренды по названию

Популярные бренды

FUJI CONTROLS IN-100, Инструкция по эксплуатации

Результаты поиска

Содержание IN-100

Отзывы:

Похожие инструкции для IN-100

Бренды по названию

Популярные бренды