Frontier ST7526 Скачать руководство пользователя страница 36

Страница: 36 / 44

10. Remove the three

fasteners

that hold the

friction wheel

to the

hub

(see Figure 50).

11. Remove the

friction wheel

from the

hub

. Slip the

friction

wheel

off the

hex shaft

12. Assemble the new

friction wheel

onto

hub

with the fasteners

removed earlier.

13. Install the

hex shaft

and

bearings

with the four bolts removed

earlier (see Figure 51).

Make sure the washers are properly installed in the original
position. Also, make sure the two washers are properly
aligned with the actuator arms.

14. Make sure the

hex shaft

turns freely.

15. Install the right wheel,

axle

, and

drive sprocket

with the fas-

teners removed earlier. Install the

chain

onto the

drive sprock-

(see Figure 48).

16. Check the adjustment of the friction wheel. See “How To

Adjust The Friction Wheel” in this section.

17. Make sure the friction wheel and the disc drive plate are free

from grease or oil.

18. Install the

bottom panel

(see Figure 47).

19. Tighten the

bolts

on each side of the

bottom panel

20. Install the

left wheel

to the

axle

with the fasteners removed

earlier.

21. Connect the spark plug wire.

Figure 51

Washer

Bearings

Washer

Actuator Arms

Bearings

Hex Shaft

Figure 50

Fasteners

Hub

Friction

Wheel

Hex Shaft

Fasteners

MAINTENANCE

Содержание ST7526













































Результаты поиска

Содержание ST7526

Отзывы:

Бренды по названию

Популярные бренды

Frontier ST7526, Руководство оператора

Результаты поиска

Содержание ST7526

Отзывы:

Бренды по названию

Популярные бренды