manualshive.com logo in svg

Frontier ST7526, Руководство оператора

Поделиться
Скачать
Frontier ST7526 Скачать руководство пользователя страница 34

HOW TO ADJUST OR REPLACE THE FRICTION WHEEL

How To Check The Friction Wheel

If the snowthrower will not move forward, check the traction drive
belt, the traction drive cable or the friction wheel. If the friction
wheel is worn or damaged, it must be replaced. See “How To
Replace the Friction Wheel” in this section. If the friction wheel is
not worn or damaged, check as follows.

1. Remove the gas from the gas tank. Stand the snowthrower up

on the front end of the 

auger housing

(see Figure 44).

WARNING: Drain the gasoline outdoors, away from fire or
flame.

2. Disconnect the spark plug wire.

3. Loosen the 

bolts

on each side of the 

bottom panel

(see

Figure 44).

4. Remove the 

bottom panel

.

5. Position the 

shift speed lever

in the lowest forward speed.

6. Note the position of the 

friction wheel

(see Figure 45). The

correct distance “

A

” from the right side of the 

friction wheel

to the outside of the motorbox is as follows: 

Tire Size

Distance “A”

12 and 13 inch

4-1/8" (10.5 cm)

16 inch

4-5/16" (10.95 cm) 

If the

friction wheel 

is not in the correct position, adjust as

follows.

How To Adjust The Friction Wheel

1. Position the 

shift speed lever

in the lowest forward speed.

2. Loosen the 

bolts

on the 

speed control rod

(see Figure 46).

3. Move the 

friction wheel

to the correct position (see Figure

45).

4. Tighten the 

bolts

on the 

speed control rod

(see Figure 46).

5. Install the 

bottom panel

(see Figure 44).

6. Tighten the 

bolts

on each side of the 

bottom panel

.

Figure 46

Loosen Bolts

Speed Control Rod

“A”

Figure 45

Figure 44

Auger

Housing

Bottom Panel

Bolt

Bolt

MAINTENANCE

34

Содержание ST7526













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды