manualshive.com logo in svg

Frontier ST7526, Руководство оператора

Поделиться
Скачать
Frontier ST7526 Скачать руководство пользователя страница 35

How To Replace The Friction Wheel

If the friction wheel is worn or damaged, the snowthrower will not
move forward. The friction wheel must be replaced as follows.

1. Remove the gas from the gas tank. Stand the snowthrower up

on the front end of the 

auger housing

(4) (see Figure 44).

WARNING: Drain the gasoline outdoors, away from fire or
flame.

2. Disconnect the spark plug wire.

3. Remove the fasteners that secure the 

left wheel

. Remove the

left wheel

from the 

axle

(see Figure 47).

4. Loosen the 

bolts

on each side of the 

bottom panel

.

5. Remove the 

bottom panel

.

6. Remove the fasteners that secure the 

drive sprocket

to the

axle

(see Figure 48).

7. Remove the right wheel, 

axle

, and 

drive sprocket

.

8. Remove the four 

bolts

that hold the 

bearings

on each side of

the 

hex shaft

(see Figure 49).

9. Remove the 

hex shaft

and 

bearings

.

NOTE: Take special note of the position of the washers on
the hex shaft.

Figure 49

Bolts

Bolts

Hex Shaft

Bearings

Figure 48

Chain

Drive Sprocket

Axle

Figure 47

Bottom

Panel

Wheel

Axle

Bolt

Bolt

MAINTENANCE

35

Содержание ST7526













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды