manualshive.com logo in svg

Frontier ST7526, Руководство оператора

Поделиться
Скачать
Frontier ST7526 Скачать руководство пользователя страница 31

How To Remove the Traction Drive Belt

If the snowthrower will not move forward, check the traction drive
belt for wear or damage. If the traction drive belt is worn or dam-
aged, replace the belt as follows.

1. Disconnect the spark plug wire.

2. Remove the auger drive belt. See “How To Remove The Auger

Drive Belt” in this section.

3. Remove the 

e-ring

from one end of the 

swing plate axle rod.

Remove the 

swing plate axle rod

to allow the swing plate to

pivot forward (see Figure 36).

4. Remove the 

traction drive spring

.

5. Remove the old

traction drive belt

from the 

traction drive

pulley

and from the 

engine pulley

. Replace the 

traction drive

belt 

with an original factory replacement belt available from an

authorized service center.

6. Install the new 

traction drive belt

onto the 

traction drive pul-

ley

and onto 

engine pulley

.

7. Make sure the 

traction drive idler pulley

is properly aligned

with the 

traction drive belt

.

8. Attach the 

traction drive spring

.

9. Install the 

swing plate axle rod

and secure with the 

e-ring

removed earlier.

10. The bottom of the 

swing plate

must be positioned between

the 

alignment tabs

. Make sure the 

swing plate

is properly

secured (see Figure 37).

NOTE: If the drive will not engage after the traction drive
belt has been replaced, then check to make sure that the
swing plate is positioned between the alignment tabs.

11. Install and adjust the 

auger drive belt

. See “How To Remove

The Auger Drive Belt” in this section.

12. Adjust the 

belt guide

. See “How To Adjust The Belt Guide” in

this section.

13. Install the 

bottom panel

(see Figure 34).

14. Tighten the 

bolts

on each side of the 

bottom panel

.

15. Install the 

belt cover

. Tighten 

screw

(see Figure 32).

16. Check the adjustment of the cables. See “How To Check And

Adjust The Cables” in this section.

17. Connect the spark plug wire.

Figure 37

Swing Plate

Alignment Tabs

MAINTENANCE

31

Содержание ST7526













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды