Frontier MS2342 Скачать руководство пользователя страница 35

Страница: 35 / 84

PROBLEM

CAUSE REMEDY

1.) Material NOT discharging

Discharge gate is NOT open.

Open gate.

from expeller.

Expeller is NOT operating.

See item #3.

Expeller is obstructed.

Activate gate to free obstruction.

Auger is not turning.

See item #2.

2.) Auger will not turn.

Shear bolts are sheared.

Replace shear bolts.

Drive chain not on sprocket.

Reinstall/replace chain.
Sprockets MUST be properly
aligned.

3.) Expeller not turning.

Shear bolts are sheared.

Replace shear bolts.

Drive chain not on sprocket.

Reinstall/replace chain.

4.) Chains are jumping drive

Inadequate chain tension.

Adjust chain tension. See

sprocket teeth.

details in Adjustments Chapter.

Sprocket teeth or
chains excessively worn.

Replace sprocket or chain.

5.) Excessive chain and/or

Sprockets are NOT properly

Re-align sprockets.

sprocket wear.

aligned.

Improper shear bolts being

Install proper shear bolts listed

used.

in Operations Chapter.

6.) Drive chain(s) will NOT

Tensioner spring(s) NOT

Adjust tensioner spring(s).

stay properly tensioned.

properly adjusted.

Idler pivot arm(s) binding.

Lubricate idler arms to pivot
freely.

Tensioner spring(s) broken

Replace spring(s).

or stretched.

7.) Uniformity of spread or

Difficult to spread material.

Change expeller or auger

discharge rate not

speed sprockets.

acceptable.

-33-

NOTE:This Troubleshooting Chapter presents problems, causes and suggested remedies beyond the
extent of loose, worn or missing parts and it was developed with th

e understanding that the

machine is

in otherwise good operating condition.

TROUBLESHOOTING

Содержание MS2342





















































































Результаты поиска

Содержание MS2342

Отзывы:

Frontier MS2342, Руководство оператора, Страница: 35 / 84

Результаты поиска

Содержание MS2342

Отзывы: