Frontier MS2342 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 84

background image

-9-

RECOGNIZE SAFETY INFORMATION

This is the safety-alert symbol. When you see this
symbol on your machine or in this manual, be alert to the
potential for personal injury.

Follow recommended precautions and safe operating
practices.

UNDERSTAND SIGNAL WORDS

A single word; DANGER, WARNING, or CAUTION is used
with the safety-alert symbol. DANGER identifies the most
serious hazards.

Safety signs with signal word DANGER or WARNING are
typically near specific hazards.

General precautions are listed on CAUTION safety signs.

FOLLOW SAFETY INSTRUCTIONS

Carefully read all safety messages in this manual, and all safety signs on your machine. Follow all
recommended precautions and safe operating procedures.

SAFETY INFORMATION

OBSERVE MAXIMUM TRANSPORT SPEED

The maximum transport speed for this implement is 32 km/h (20 m.p.h.).

Some tractors are capable of operating at speeds that exceed the maximum
transport speed of this implement. Regardless of the maximum speed capability
of the tractor being used to tow this implement, do not exceed the implement’s
maximum transport speed.

Exceeding the implements maximum transport speed can result in:

* Loss of control of the tractor/implement combination
* Reduced or no ability to stop during braking
* Implement tire failure
* Damage to the implement structure or its components

Use additional caution and reduce speed when towing under adverse surface
conditions, when turning, and when on inclines.

Do not attempt transport if the fully loaded implement weighs more than 1.5 times
the weight of the tractor.

Keep signs in good condition. Immediately replace any missing or damaged signs.

«
...
9
10
11
12
13
...
»

Содержание MS2342





















































































Отзывы:

Нет отзывов

Похожие инструкции для MS2342

Card Reader RCR103

Бренд: Rosewill Страницы: 3

Бренд: Magtek Страницы: 2

Бренд: Identiv Страницы: 40

Бренд: Gemalto Страницы: 9

Бренд: QVSR Страницы: 4

Бренд: Samsung Страницы: 36

Бренд: Velleman Страницы: 2

Бренд: Velleman Страницы: 32

Бренд: IVDT Страницы: 13

Бренд: Visonic Страницы: 2

Бренд: Visonic Страницы: 2

Бренд: IDTECK Страницы: 23

PowerExpand A8328

Бренд: Anker Страницы: 9

PowerExpand A8326

Бренд: Anker Страницы: 12

Бренд: Kärcher Страницы: 76

Бренд: Targus Страницы: 8

Бренд: POSline Страницы: 6

Бренд: Orgautomatech Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды