Frontier MS2342 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 84

background image

LUBRICATION

GREASING

There are numerous grease fittings on the Manure Spreader. Lubricated properly and often with a
high-quality grease, will prolong the life of the spreader. Replace any missing or plugged grease fittings.

Wipe dirt from the fittings before greasing to prevent the dirt from being forced into the bearing or pivot.
Grease should come out around the shaft on sleeve type bearings. On the sealed ball bearings, grease
should be added slowly until a slight bead forms at the seal indicating the correct amount of lubricant. To
minimize dirt build-up, avoid excessive greasing. After greasing, wipe off the excess grease from around
the outside of the bearings to prevent the accumulation of chaff and grit.

NOTE:

Grease all fittings at the intervals of operation listed, before and after storing the Manure Spreader.

Use a good grade of Lithium-base grease.

-30-

PTO Shaft - As required by Manufacturer

Axle Hubs

Rear Expeller Bearing

Expeller Pan Release Pivot

Rear Auger Slide Plate (4 Zerks)

Rear Auger

Bearing

Grease Fitting Locations - Grease Every 10 Hours (or Daily)

«
...
30
31
32
33
34
...
»

Содержание MS2342





















































































Отзывы:

Нет отзывов

Похожие инструкции для MS2342

Бренд: Happowa Страницы: 18

Бренд: Farpointe Data Страницы: 2

Бренд: Farpointe Data Страницы: 2

Бренд: HP Страницы: 52

FL863UT - Workstation - Z400

Бренд: HP Страницы: 222

FL863UT - Workstation - Z400

Бренд: HP Страницы: 10

Бренд: HP Страницы: 10

FL863UT - Workstation - Z400

Бренд: HP Страницы: 9

FZ-VSC552 Series

Бренд: Panasonic Страницы: 6

FZ-VSC551 Series

Бренд: Panasonic Страницы: 8

FlashMover 23-in-1 USB2.0

Бренд: Microdia Страницы: 2

Бренд: Manhattan Страницы: 2

Бренд: Manhattan Страницы: 8

Бренд: Kaba Страницы: 82

i-scan ID ISC.LRU2000-A-EU

Бренд: OBID Страницы: 56

Бренд: IRIS Spreaders Страницы: 49

Бренд: xpr Страницы: 4

Бренд: Targus Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды