Frontier MS2342 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 84

background image

GENERAL INFORMATION

IMPORTANT: Catch and dispose of fluid per local waste disposal regulations whenever service is
performed on hydraulic components, valves, cylinders, hoses, etc.

LUBRICATION

Become familiar with all lubrication points and establish a routine to ensure complete lubrication of
the

Manure Spreader

.

-28-

PTO ASSEMBLY

Keep the male and female shafts of the PTO well lubricated and free sliding.
Failure to observe this precaution will result in excessive pressure being
required to collapse or extend the assembly while subject to operating torque.
This excessive force may damage the main shaft bearings. Never lubricate
the shield surfaces. The shield surfaces must be kept dry, as dirt
accumulation on them will cause the shields to bind and not rotate.
Dented or damaged PTO shields, will also result in excessive force being
applied against the jackshaft. Damaged shields also cause difficulty when
installing the assembly. If at any time the shields do not turn freely, they should
be checked to determine the cause, and repaired or cleaned. To avoid
damage to the main drive bearings, avoid turning sharp corners while PTO is
running. Start and Stop PTO slowly to avoid damage to the drive line.

WHEEL BEARING LUBRICATION, CLEAN & RE-PACK INSTRUCTIONS

Grease wheel bearings as needed depending on amount of travel.

Wheel hubs are equipped with a grease zerk for regular
maintenance.

Annually disassemble and clean parts in a solvent. Pack bearings
with a high grade grease. Reassemble, and tighten nut until a slight
drag is felt when wheel is turned. Back nut off and insert cotter pin
into first hole that you see as you back the nut off, bend cotter pin
over and re-install cap.

«
...
28
29
30
31
32
...
»

Содержание MS2342





















































































Отзывы:

Нет отзывов

Похожие инструкции для MS2342

Бренд: Renkforce Страницы: 4

MINI SPREADER 36000

Бренд: Meyer Страницы: 3

Бренд: StarTech.com Страницы: 2

Бренд: Unigreen Страницы: 20

DMS-3PT-12V-4.5-TSC

Бренд: Fimco Страницы: 6

Бренд: FAMOCO Страницы: 23

TruPortal T-200

Бренд: Interlogix Страницы: 2

CAMEDIA MAUSB-1

Бренд: Olympus Страницы: 29

Бренд: Icidu Страницы: 5

Emerchantpay PAX A920

Бренд: Handpoint Страницы: 11

Бренд: Salto Страницы: 4

ExpressCard 2000

Бренд: Magtek Страницы: 12

Бренд: GFE Страницы: 44

Бренд: Hama Страницы: 36

Бренд: ACT Страницы: 2

Бренд: SIIG Страницы: 8

Бренд: SIIG Страницы: 4

USB 3.0 Flash Memory Card Reader

Бренд: SIIG Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды