Frontier MS2342 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 84

Frontier MS2342 Скачать руководство пользователя страница 14

TRACTORS:

This Operators Manual uses the term “Tractor” when identifying the the power source.

TO PREVENT SERIOUS INJURY OR DEATH

Study The Above Safety Rules

ATTENTION - BE ALERT - YOUR SAFETY IS INVOLVED

BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING
INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS
WITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE
SAFETY PRECAUTIONS.

Frontier always takes the operator and their safety into consideration and guards exposed moving
parts for their protection. However, some areas cannot be guarded or shielded in order to assure proper
operation. In addition, the Operators Manual and decals on the Manure Spreader itself warn you of further
danger and should be read and observed closely.

-12-

KNOW HOW TO STOP MACHINE BEFORE STARTING IT.

I

f the machine becomes clogged or for servicing, Stop the tractor engine, remove ignition key and

allow all mechanisms to stop. Before cleaning or working on the machine, detach the PTO shaft, and
completely disengage the tractor hydraulics.

DO NOT

attempt to perform maintenance or repair with tractor running, and PTO, and hydraulic hoses

connected to the tractor.

DO NOT

step up on the Manure Spreader at any time while in operation.

NEVER

manually feed material into the expeller.

DO NOT

allow minors to operate or be near the Manure Spreader.

DO NOT ALLOW PERSONNEL OTHER THAN THE QUALIFIED OPERATOR NEAR THE MANURE
SPREADER.

STAY CLEAR

of discharge expeller when in operation.

Keep hands, feet, and clothing away from all moving parts when the Manure Spreader is in operation.

Loose or floppy clothing should not be worn by the operator.

Be sure the Manure Spreader is clear of people, tools, and other objects before engaging PTO.

Do not step over PTO shaft: Stay clear of PTO at all times.

NEVER

start the Manure Spreader until all guards and safety shields are secured in place.

Never operate the Manure Spreader with a PTO speed greater than the recommended PTO RPM.

STAY CLEAR

of hydraulic lines, they may be under extreme pressure or heat.

«
...
12
13
14
15
16
...
»

Содержание MS2342





















































































Отзывы:

Нет отзывов