manualshive.com logo in svg

Frontier DM1160, Руководство оператора

Поделиться
Скачать
Frontier DM1160 Скачать руководство пользователя страница 54

52

Maintenance and storage

DM1160

Cutterbar draining and refilling

From the transport position:

- Place a container of sufficient capacity under drain

plug.

- Remove filler plug (1) and its washer.
- Remove drain plug (2) and its washer.
- Allow oil to drain completely.
- Wait for dripping to stop.
- Clean and reinstall drain plug (2) and its

washer. Replace if necessary.

- Pour the correct oil quantity and quality through the

opening of the filler plug.

- Clean and reinstall filler plug (1) and its

washer. Replace if necessary.

Before draining oil, operate the machine for a
few minutes so that the oil warms up.

The cutterbar is lubricated with 2.25 L (0.59 US gal) of extreme-pressure gear oil with viscosity grade
SAE 80W90 and API grade GL5.

When draining and refilling, it is recommended to use either a mineral base oil with viscosity grade SAE
80W90 and API grade GL5, or a synthetic base oil, type PAO (Poly-Alpha-Olefins) with a viscosity grade
equivalent to SAE 80W90. 

Never use an oil of viscosity SAE 90 in the
cutterbar. 

1

2

Содержание DM1160





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды