Fronius AccuPocket 150/400 TIG Скачать руководство пользователя страница 58

Страница: 58 / 88

Removing the re-
chargeable bat-
tery pack

NOTE!

The following steps on removing the rechargeable battery pack must only be
used when disposing of the device!

▶

If the rechargeable battery pack needs to be repaired or replaced, contact
After-Sales Service.

NOTE!

Before removing the rechargeable battery pack, the power source must be dis-
connected from the battery charger!

▶

Ensure that the power source is completely discharged.

Remove the control panel

Disconnect the (+) power cable from the re-

chargeable battery pack, remove 2 TX25 screws

Remove 2 TX25 screws, remove device feet at

the front

Remove 2 TX25 screws, remove the cover

Содержание AccuPocket 150/400 TIG

























































































Результаты поиска

Содержание AccuPocket 150/400 TIG

Отзывы:

Похожие инструкции для AccuPocket 150/400 TIG

Бренды по названию

Популярные бренды

Fronius AccuPocket 150/400 TIG, Руководство по эксплуатации

Результаты поиска

Содержание AccuPocket 150/400 TIG

Отзывы:

Похожие инструкции для AccuPocket 150/400 TIG

Бренды по названию

Популярные бренды