Fristam Pumps FP Скачать руководство пользователя страница 8

Страница: 8 / 40

/ / FP PUMP SERIES / / /

Impeller (13)

Open impellers are standardly used in the FP pump series.

Pump Cover (14)

The connection for the suction line is located on the pump
cover.

Pump Casing (16)

The connection for the discharge line is located on the pump
casing. The impeller and the shaft seal are built into the pump
casing.

3.1.2

Lantern (B) and Electric Motor (C)

Fig. 7

Lantern and electric motor

Lantern (17)

The lantern is present in all models except the special motor.

The lantern connects the pump casing to the motor. Two
different versions are possible, depending on pump size:

– The pump casing is screwed to the lantern via a flange con-

nection.

– The pump casing is inserted into the lantern and mounted

with a clamp.

Models with lanterns:

– FPE and FP…V

– KF



An additional bearing for the pump shaft is located inside
the lantern with base.

– L



An additional bearing for the pump shaft is located inside
the lantern with base. The pump shaft is connected to the
motor via a coupling.

Electric Motor (19)

The following motor types can be mounted:

– IEC standard motor with drive side fixed bearing (A side),

feather key and shaft pin of the following types:

– IM B3: model with base

– IM B5: model with flange

– IM B3/5: model with flange and base

With the IEC standard motor, a

Fristam

pump shaft is

clamped to the motor shaft pin.

– Special motor with

Fristam

pump shaft

With the special motor, the

Fristam

pump shaft is already in-

tegrated and connected permanently to the motor.

3.2

Models

The model is indicated on the rating plate. See

Chapter 2.4.4,

"Rating Plate," page 6

The following are shown as examples:

– Lantern clamp-mounted

– Without enclosure



See

Chapter 3.4, "Versions," page 9

3.2.1

Model FP

Fig. 8

Model FP

3.2.2

Model FPE or FP…V

Fig. 9

Model FPE or FP...V

Lantern

Electrical connection

Electric motor

Pump shaft

Motor:

Special motor

Design:

Without lantern

Motor:

IEC standard motor, model B3/B5

Design:

With lantern

Содержание FP









































Результаты поиска

Содержание FP

Отзывы:

Fristam Pumps FP, Оригинальные инструкции, инструкции по сборке, Страница: 8 / 40

Результаты поиска

Содержание FP

Отзывы: