manualshive.com logo in svg

Fristam Pumps FP, Оригинальные инструкции, инструкции по сборке, Страница: 36 / 40

Поделиться
Скачать
Fristam Pumps FP Скачать руководство пользователя страница 36

/ / FP PUMP SERIES / / /

36

Incorrectly Designed Motor and Coupling

Destruction of pump and coupling.

►

Only use motors and couplings that have been adapted to 
the pump characteristic curves. If you have any questions, 
please contact 

Fristam

. 

Note: Please see the coupling supplier documentation for 
reference dimensions for the coupling. 

Procedure 

1. Mount the coupling parts on the pump shaft and the gear 

shaft. 

2. Place the pump on the base frame or the foundation so that 

the pump shaft can be connected to the gear shaft with the 
coupling. 

3. Screw the threaded fastener slightly into the pump base. 

4. Check the parallel and angular misalignment of the pump 

and gear shafts.

5. Minimize deviations from the angular and shaft misalign-

ment. If necessary, realign or add shims. 

6. Screw the pump and gear to the base frame or the founda-

tion. 

7. Fasten the coupling according to the coupling manufactur-

er's specifications. 

8. Install a noncontact, barrier-providing protective device 

(coupling guard) in accordance with 

Section 1.4, entitled "Re-

quired Characteristics of Guards and Protective Devices," of the 
Machinery Directive 2006/42/EC

. 

9. The pump is now installed. Do not commission the pump 

unless the requirements of the EC Machinery Directive are 
met for the complete machine. 

Note: Continue with 

Chapter 4, "Transportation," page 9

. 

Содержание FP









































Отзывы:

Нет отзывов