manualshive.com logo in svg

Fristam Pumps FP, Оригинальные инструкции, инструкции по сборке, Страница: 12 / 40

Поделиться
Скачать
Fristam Pumps FP Скачать руководство пользователя страница 12

/ / FP PUMP SERIES / / /

12

►

Versions B and D:

Screw the pump on the compact bearing support with base 
to the foundation.

Model L 

►

Versions A and C:

Set up the pump on the spherical cap bearings and align.

►

Versions B and D:

Screw the pump on the base frame to the foundation.

Carriage (Optional)

1. Set up the pump at the installation location. Lock the locks 

on the rollers (if present) or secure the carriage with chocks. 

2. Ground the carriage to dissipate electrostatic charge. 

3. Position hose line to ensure that it cannot be damaged.

6.4.1

Installation of Pipes

►

Lay and connect pipes as follows:

– Keep the pipe resistance as low as possible: Avoid unnec-

essary installation of valves, elbows, and abrupt pipe 
transitions.

Fig. 15

Pipe transitions

– Design pipe cross section so that no unnecessary pres-

sure losses or cavitation occurs in the suction area and so 
that the condition

NPSH

a

 > NPSH

r

is fulfilled. 

Verify this in the project planning stage.

– Install the suction lines in horizontal position or at a con-

stant dropping angle towards the pump unit. Rule out 
the possibility of air pockets and dips in the pipes.

Fig. 16

Air pocket

Fig. 17

Dip in pipe

– Pipe bends upstream of suction connection: Heed mini-

mum clearance and minimum bend radius:

Fig. 18

Laying of the suction line

– Connect the pipes to the pump so that they are free of 

tension and compression to ensure that no stresses are 
applied to the pump.

– Secure pipes to ceilings, walls, or floor using pipe clamps. 

– Align pipes flush with pump connections using a bracket. 

6.5

Electrical Connection

Electrical connection may only be performed by a qualified 
electrician.

1. Heed the connection values on the motor's rating plate. The 

specified voltage must not be exceeded.

2. Connect the motor according to the circuit diagram in the 

terminal box of the motor.

3. Protect cable feedthroughs against penetration by moisture.

4. Turn on the motor for 2 to 3 seconds. Compare the direction 

of rotation of the motor fan wheel against the direction indi-
cated by the arrow on the pump head.

5. Reverse the polarity if necessary.

5 - 10 x D

R ≥ 2 x D

D

Содержание FP









































Отзывы:

Нет отзывов