manualshive.com logo in svg

Fristam Pumps FP, Оригинальные инструкции, инструкции по сборке, Страница: 25 / 40

Поделиться
Скачать
Fristam Pumps FP Скачать руководство пользователя страница 25

25

Application Case E

Fig. 44

Application case E

In the above figure, parts are grouped according to assembly 
steps:

Fig. 45

Application case E, assembly of motor-side shaft seal (I)

To assemble the shaft seal on the motor side 

(I)

:

1. Only for FP...V: Secure the set collar 

(50-3.60)

 to the shaft 

using set screws 

(904.61)

. 

Apply a screw retaining compound to the set screws. Posi-
tion on the shaft: See “

Sectional Drawing

“.

2. Slide the washer 

(550.62)

 onto the shaft. 

3. Equip the rotating seal ring 

(472.61)

 with an O-ring 

(412.66)

.

4. Slide the spring 

(479.60)

 with the thrust collar 

(474.61)

 and 

the rotating seal ring 

(472.61)

 onto the shaft. Let the folded 

end of the spring snap into the slot on the rotating seal ring.

5. Mount the pump casing; see 

Chapter 9.10.3, "Mounting of the 

Pump Casing," page 25

.

6. Insert the O-ring 

(412.67)

 into the stationary seal 

ring 

(475.61)

 and insert into the mechanical seal 

chamber 

(47-2.60)

.

Assembly of the shaft seal on the motor side is now finished.

To assemble the shaft seal on the pump side 

(II)

:

7. To assemble the shaft seal on the pump side, proceed as de-

scribed in 

Chapter , "Application Case A," page 21

.

Application Case F

Fig. 46

Standard shaft seal, application case F

To assemble the motor-side shaft seal 

(IV)

 on the shaft:

Fig. 47

Motor-side shaft seal (IV), application case F

►

Slide the spring 

(479.50)

 with the thrust collar 

(474.51)

, the 

O-ring 

(412.54)

, the rotating seal ring 

(472.51)

, the 

stationary seal ring 

(475.51)

, and the O-ring 

(412.53)

 onto 

the shaft. Let the folded end of the spring snap into the 
rotating seal ring.

To assemble the pump-side shaft seal 

(I)

:

►

Assemble the pump-side shaft seal (I) as described in 

Chapter , "Application Case B," page 22

.

9.10.3 Mounting of the Pump Casing

Pump With Flange Connection

Fig. 48

Mounting of the pump casing with a flange connection

I

Assembly of the shaft seal on the shaft on the motor side

II

Assembly of the shaft seal on the shaft on the pump side

II

I

475.61

412.67

472.61

474.61

412.66

479.60

550.62

904.61

50-3.60

I

Pump-side shaft seal

IV

Motor-side shaft seal

I

IV

412.53

475.51

472.51

412.54

474.51

479.50

52

53

54

Содержание FP









































Отзывы:

Нет отзывов