background image

15

920-087-06

Section III – Chassis Installation

1.  Remove the weatherboard and center support from the sleeve 

(if still in place). Be sure an outdoor grille is attached.

Check to be sure the wall sleeve, extension (if used), grille, and drain kit are installed properly before chassis installation.

2.  Remove the front cover contained in a protective plastic bag 

from chassis. Remove the bag and dispose of it properly.

  If the control door is not installed, follow these steps:
•  From the front of the cover, slide the right control door pin 

into the hole on the right side of the front cover. Slide the 

left door pin into the hole on the left side of the front cover 

opening and snap it into place.

3.  Remove the two chassis shipping brackets from the ends 

of the shipping pallet.

NOTE:  To avoid breaking the door or hinge pins, do not apply 

excessive force when installing

Suffocation hazard
Keep bag away from babies and children.
Do NOT use in cribs, beds or playpens.  Destroy 

immediately after opening. This bag is NOT a toy.
Failure to do so can result in personal injury and/or death

IMPORTANT:  Use a wall sleeve adapter kit (PXSE) if 

installing a P-Series chassis in a T-Series sleeve.

Compressor

Chassis 

shipping bracket

Shipping pallet

IMPORTANT:  When installing a Friedrich P-Series PTAC into an 
existing sleeve, it is important to ensure that the unit is installed 
completely.  Inspection of the air seal between the condenser air 
baf

fl

 es and around the indoor mounting 

fl

 ange is recommended.  

In some cases additional gaskets or baf

fl

 ing may be required.

Wall sleeve

Weatherboard

Center support

1

Control 
Door

Pins

Front Panel

2

3

Installation Checklist

  

Inspect all components and accessories for damage 

before and after installation.

  

Remove the cardboard wall sleeve support and grille 

weatherboard.

  

Check for proper wall sleeve installation in accordance 

with the wall sleeve installation instructions.

  

Check for a subbase kit or other means of structural 

support which is required for ALL installations projecting 

more than 8" into room.

  

Install the recommended Condensate Drain Kits for 

complete condensate removal.

  

Ensure that the chassis is installed in a 16" high x 42" 

wide wall sleeve that is no deeper than 13 ¾".  A baf

fl

 e kit 

is required if the sleeve exceeds that depth.

  

Ensure that drapes, bed, bedspread, furniture, etc. DO 

NOT block either return or discharge air grilles.

  

Inspect the condenser air inlet and outlet for any 

obstructions (shrubbery, etc.)

  

Ensure that 'reset' button is pressed on LCD device (only 

on cord connected models)

WARNING

Содержание PDH07K3SB1






























Отзывы: