Freggia DWI4108, Руководство пользователя

Страница: 11 / 44

GB
11
FAILURE CODES AND WHAT TO DO IN CASE OF FAILURE
SWITCHING ON THE MACHINE AND SELECTING A PROGRAMME
• INNER LIGHT OPTION:
The door must be at OPEN position during activation and deactivation of inner light
modes.
• HOW TO CHANGE FROM “ECO MODE” TO “NORMAL MODE” FOR INNER
LIGHT OPTION:
• First open the dishwasher door and energize the machine via main switch
(if it is in OFF position).
• Press ‘’3in1’’(5) and ‘’1/2’’(6) buttons simultaneously for 3 seconds.
• “IL0” will be shown in the digit display for 2 seconds to show the “Normal
Mode” is selected for inner light option.
• After “Normal Mode” is selected, the inner light will be ON as long as the
machine is energized and machine door is open.
• HOW TO CHANGE FROM “NORMAL MODE” TO “ECO MODE” FOR INNER
LIGHT OPTION:
• First open the dishwasher door and energize the machine via main switch
(if it is in OFF position).
• Press ‘’3in1’’(5) and ‘’1/2’’(6) buttons simultaneously for 3 seconds.
MAINTENANCE AND CLEANING
CLEANING THE MACHINE IN REGULAR INTERVALS PROLONGS
THE MACHINE’S SERVICE LIFE.
• OIL AND LIME MAY ACCUMULATE IN THE MACHINE’S WASHING SECTION.
IN CASE OF SUCH ACCUMULATION;
• Fill the detergent compartment without loading any dishes into the
machine, select a programme that runs at high temperature, and start the
machine. In case of insuffi
ciency, use special cleansing material available
in the market. (Cleansing material produced special to machines by
detergent producers.)
• CLEANING THE SEALS IN THE MACHINE DOOR
• To clean any accumulated residues in the door seals, wipe the seals
regularly by using a dampened cloth.
• CLEANING THE MACHINE
Clean the fi lters and spray arms at least once a week.
Unplug your machine and turn off its tap before starting the cleaning.
Do not use hard materials when cleaning your machine. Wipe with a fi ne cleaning
material and a dampened cloth.
• FILTERS
Check if any food wastes have remained on the coarse and fi ne fi lters.
If any food wastes are left, remove the fi lters and clean them thoroughly under the
water tap.
a. Micro Filter
b. Coarse Filter
c. Metal/Plastic Filter
To remove and clean the fi lter
combination, turn it counter
clockwise and take it out by lifting
upwards. 1 Pull and remove the
metal/plastic fi lter. 3 Then pull
the coarse fi lter out of the micro
fi lter.2 Rinse it with lots of water
under the tap.
Refi t the metal/plastic fi lter. Insert the coarse fi lter into the micro fi lter in a way that
the marks will correspond to one another. Attach micro fi lter into the metal/plastic
fi lter and turn to the direction of arrow and it is locked when the arrow on micro fi lter
can be seen from across. 4
• Never use your dishwasher without any fi lter.
• Incorrect fi tting of the fi lter will reduce the washing eff ectiveness.
• Clean fi lters are very important in terms of the proper running of the
machine.
• SPRAY ARMS
Check whether or not the holes for the upper
and lower spray arms are clogged. If there is any
clogging, remove the spray arms and clean them
under water.
You can remove the lower spray arm by pulling it
upwards, while the upper spray arm nut can be
removed by turning the nut to the left.
Be sure that the nut is perfectly tightened when
refi tting the upper spray arm.
• HOSE FILTER
Water is prevented by the inlet hose fi lter so as to avoid any damage to your machine
because of any contamination (sand, clay, rust etc.) that might be occasionally carried
in through the mains water supply or the indoor plumbing, and to forestall such
complaints as yellowing and formation of deposits after washing. Check the fi lter and
the hose from time to time and clean them if necessary. To clean the fi lter, fi rst turn off
your tap and then remove the hose. After removing the fi lter from the hose, clean it
under the tap. Insert the cleaned fi lter back into its place inside the hose. Refi t the hose.
• “IL1” will be shown in the digit display for 2 seconds to show the “Eco
Mode” is selected for inner light option
Also inner light turns OFF and ON again (blinks momentarily) to show this selection
is activated.
• After “Eco Mode” is selected, the inner light will be ON for 4min after
machine door is opened and then turns OFF. If any user intervention
occurs such as pressing buttons, Eco Mode cycle starts from beginning
(inner light is ON for 4min and then becomes OFF again)
Note:
Factory setting for inner light are set to ‘’IL1’’.
NOTES:
For FI productions , the inner light setting should be allowed only if the door
is open condition.