manualshive.com logo in svg

Freedom Won LiTE Business 40/32, Руководство по установке

Поделиться
Скачать
Freedom Won LiTE Business 40/32 Скачать руководство пользователя страница 28

Freedom LiTE Installation Manual Revision 14 

 

                        P a g e  

27 | 30

 

 

2.

 

Battery has been discharged to critically low 
level 

–

 remove all potential loads from the 

battery and switch off the inverter(s). Then try 
to switch on the BMS. 

3.

 

Battery has been charged to critically high 
voltage level 

–

 usually leaving the battery for an 

hour will allow the cell levels to drop down 
within acceptable levels and allow the BMS to 
be switched on again.  

4.

 

Hold the ON button for at least 5 seconds. 

5.

 

If the BMS still does not switch on, please 
contact Freedom Won or Authorised Distributor 

 

4 

The main breaker switch keeps 
tripping each time I attempt to 
switch it on 

There are several potential causes: 

1.

 

The Battery Management System has not been 
switched on. The ON button must be pressed for 
5 seconds. On release the SoC Display must 
remain illuminated.  

2.

 

High inrush current on certain inverters 

–

 First 

preference is to pre-charge the DC bus by 
switching on the solar charge controllers if 
present and in daytime. If this is not possible 
switch on the AC feed into the inverter and 
switch on the inverter. Some makes will then 
pre-charge the DC bus. You can also use a pre-
charge resistor for this. If this does not work 
after the second attempt investigate the other 
options.  

3.

 

Short circuit on the DC Bus or faulty inverter or 
MPPT causing high currents 

4.

 

In a system with multiple LiTEs in parallel the 
reason could be that the battery you are trying 
to switch on is at a different voltage to the 
others 

–

 the voltages must be similar (within 2V 

of each other) on all batteries when switching 
them onto a common DC bus.  

 
If none of the above solve the problem, you will need to 
contact Freedom Won or your authorised installer for 
assistance with this issue.  
 
It will be necessary to establish the reason for the error 
before continuing with normal operation of the system. 
Repeated tripping is damaging for the breaker.  

5 

After resetting the BMS the main 
breaker still will not stay up.  

This is most likely because the battery is fully discharged 
and the BMS is protecting the cells from further 
discharge. Ensure that there is no chance of load being 
applied to the battery by isolating the AC output from 
the inverter. Ensure that the AC input to the inverter is 
live so that the charger may begin charging the battery 
after you switch it on. Alternatively, an MPPT can be 

Содержание LiTE Business 40/32































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды