manualshive.com logo in svg

Freedom Won LiTE Business 40/32, Руководство по установке

Поделиться
Скачать
Freedom Won LiTE Business 40/32 Скачать руководство пользователя страница 27

Freedom LiTE Installation Manual Revision 14 

 

                        P a g e  

26 | 30

 

 

11.3

 

Storage 

The ideal storage temperature for a LiTE in long term storage is 15 to 25 degrees Celsius. 
Storage at temperatures higher than 25 degrees Celsius is not recommended. Store in a dry 
environment away from corrosion agents.  

 

12.

 

Troubleshooting Guide 

Most issues with the Freedom LiTE can be resolved using the guide below. If a problem 
cannot be resolved after referencing this table, please contact Freedom Won or your 
approved Freedom Won supplier. 

Table 14.1 Troubleshooting Guide (applicable to units with On and OFF buttons) 

No  Problem Description 

Cause/Solution 

1 

Eye bolts do not screw into hard 
point on top of Freedom LiTE 

Check that you have the correct eye bolt with the 
correct thread pitch 

–

 M12 x 1,75  

2 

The rawl bolt head does not fit 
into the hole on the back of 
Freedom LiTE (wall mounted 
models) 

Check that you are using the correct size Rawl Bolt as 
specified in this manual and that you have after 
positively tightening the internal gripping collar turned 
the bolt out again so that there is about 5mm of the bolt 
shank exposed so that the back plate can fit easily 
behind the bolt head. If the wall is uneven, it may be 
necessary to turn the bolt head out a little more. Do not 
turn it so far out that there is less than the full thread 
length engaging on the internal locking collar.  

3 

The Freedom LiTE has no voltage 
on the main output cables 

Check that you have switched on the main breaker 
switch. Note 

–

 only turn this on once you are satisfied 

that you have completed the installation and that there 
are no DC or control wires that can short out or touch 
ground or other wires. Also ensure that you are ready to 
accept AC voltage onto the inverter output before 
switching this breaker on. Also confirm that you have 

energised the BMS first by pressing the “ON” button 

for 

5 seconds and as evidenced by the lights on the SoC 
display.  
Ensure that the breaker lever is in fact all the way up 

and not in he tripped position. If the lever is in the “60% 

position

”, push

 the lever down all the way before 

pushing it up.  
If voltage is still not present with the breaker switched 
on it is possible the breaker has been damaged 

–

 please 

contact Freedom Won 

4 

The BMS power (indicated by 
battery SoC display lighting up) 
does not stay on after the ON 
button is pressed 

1.

 

Error on the BMS. Check whether the red error 
light is illuminated on the SOC display when the 
ON button is held in. You can try to reset the 
error by pressing the RESET button for about 2 
seconds and release. This should clear the error 
and allow the BMS to stay on after releasing the 
ON button. 

Содержание LiTE Business 40/32































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды