background image

24

EN

No.

Scope

Actions

1

General control

Perform firing up procedure in the heater. Check the operation of 

all security systems. Check if the main burner flame burns steadily. 

Check that the main burner burns evenly.

2

Windshield 

control

Check the glass for cracks

Check the degree of dirt on the glass. Clean the glass if necessary.

3

Control of gas 

control system

Check the gas connections for leaks.

Check that the cylinder chamber ventilation is not blocked.

Check that the cables connecting the controller to the receiver are 

not damaged.

Check that the gas control system components are not exposed to 

high temperatures.

Check that the inner chamber and the elements installed in it are 

not exposed to moisture. Check that the connecting cables show no 

signs of corrosion.

4

Combustion 

chamber control

Check that the control burner is not obstructed by decorative 

elements.

Check if the thermocouple is within the control flame. Check whether 

the combustion chamber requires cleaning.

Check that all air inlets to the combustion chamber are clear. If 

necessary, clear the holes.

Check the combustion chamber for signs of corrosion. If necessary, 

remove corrosion and cover the defects with a new layer of fireplace 

paint.

Check if the main burner ignites smoothly.

5

Control device 

control

Check that the components of the control system are not exposed 

to overheating.

6

Decorative 

elements

Check if the decorative elements require cleaning.

Check that the decorative elements are not in contact with the glass.

Check if the decorative elements cover the openings venting the 

hearth.

Check that the decorative elements have not been damaged.

Checklist:

ENVIRONMENTAL PROTECTION

• 

All packaging components in which the gas heater has been supplied should be disposed of in a 

manner appropriate to their type.

• 

Due to the content of heavy metals, batteries are classified as hazardous chemical waste, so after 

using them, they should be thrown into special containers for hazardous waste.

• 

If the device is used up again, it must be disposed of. The user is obliged to pass the fireplace to the 

appropriate institution dealing in the recycling of this type of equipment.

Содержание OUTDOORFIRE B


























Отзывы: