FPI Dell-Point GF45, Инструкция для владельца и по установке

Страница: 16 / 28

Greenfi re GF45 BioEnergy Stove 16
OPERA
TION
OPERATING INSTRUCTIONS
Priming Stove: Empty Hopper
1) Open the Hopper Lid and fi ll with desired fuel to be burned.
NOTE: The Hopper can hold up to a 45 pound bag of fuel.
2) Close Hopper Lid.
3) Open the front door and place the measuring cup in the center of the burn
pot directly under the feed tube. The measuring cup will need to be tilted
in order to fi t under the feed tube.
4) Close the Front Door.
5) Open the Control Panel Cover and press the “Prime Stove” button once.
The Control Panel screen will display Prime Feed .
6) Wait 2 minutes to allow for the stove to prime. While the stove is priming
you will see fuel spilling into the measuring cup.
7) After 2 minutes the Control Panel will return to the main screen. Open
the front door and remove the measuring cup from the burn pot and pour
the fuel back into the hopper.
8) Close Hopper Lid and Front Door.
9) Proceed to the steps below to burning the desired fuel type.
NOTE: If the stove does not prime within 2 minutes, ensure that the Hopper
Lid and Front Door are properly closed. (The stove will not prime if the
front door or hopper lid are open.) Press the “Prime” button again.
Burning Wood Pellets: Primed Hopper
NOTE: If the hopper is empty, follow steps 1 to 8 to Prime Stove.
1) Open the control panel cover, and select the fuel type by pressing the
“Select Fuel” button until the screen displays
Wood . The optional Green-
Key is only needed for additional fuels, without it the unit will burn wood
pellets only.
2) To ignite the stove press the “Start” button once and the screen will display
Ignition . Do not add any fuel to the burn pot. In Wood mode the stove
will fi ll the burn pot before starting ignition.
3) The ignition sequence will take approximately 7 minutes to complete.
After 3-4 minutes you should start to see smoke coming from the burn
pot.
This is normal , it means that the igniter is working. When the pellets
ignite and fl ames appear the smoke will disappear.
IMPORTANT:
On start up, always use wood pellets when
operating unit from a cold start. Wood pellets
ensure a faster and hotter starting fi re which
results in better performance.
STARTING
PROCEDURES
CAUTION: Do Not use the manual priming procedure for
starting of your stove as this may cause smoke in your resi-
dence. Like all solid fuel fi res, the initial start-up is crucial to
the ongoing performance of your appliance. Failure to start
your fi re properly can lead to frustrations and continued
re-light attempts.
To Start Your Stove
To facilitate your start up and regardless of fuel being utilized in your
stove, you must use wood pellets as fuel for starting. This will quickly
raise the burner and vent temperatures providing a better and faster start
up. Failure to use wood pellets will not ignite the stove.
Before starting
each fi re, fi rst make sure the burn pot is completely emptied out.
Never attempt to start with a partly fi lled burn pot.
OPERATION GUIDELINES FOR
BURNING CORN & WHEAT
IMPORTANT: Compared to wood pellets, agricultural based
fuels such as Corn or Wheat require extra care, attention
and understanding. Failure to adhere to these operating
instructions could lead to Ash Auger failure, and /or build up
of ash in the Burn-pot leading to system failure. Such issues
are at the control of the operator and not to be considered
appliance problems. The physical characteristics and
composition of Corn and Wheat, are very different to that
of wood. Following these guidelines and directions will help
you better understand and control the performance of your
appliance while burning Corn or Wheat.
When burning Corn or Wheat, the following will help you understand and
establish control of the working parameters of the appliance for optimum
performance during operation.
Initial Use Of GF45 For
Burning Corn & Wheat
In order to become better acquainted with this new technology, we recom-
mend to the fi rst time user of wood pellet fuel only for the fi rst few days.
Once you are comfortable with the functions of the control pad and the
changes in operation when using the controls with wood pellets, you can
feel safe to move on to burning Corn or Wheat. Remember regardless
of the fuel you will be burning from your hopper,
wood pellets must be
used to start your fi re .
NOTE: To further ensure your start-up, after the initial 37 minutes, you
now have control of the keypad for adjustment purposes. However, the
keypad is protected to only allow single incremental rises and drops in
fuel feed for 25 minutes at a time. This means should you enter two level
changes to feed rate, i.e. from 3 to 5, the feed rate will fi rst stabilize on
4 (3 lbs per hour) for a period of 25 minutes before increasing to 5 (4 lbs
per hour). This is to allow the fi re to build up rather than create a potential
for extinguishing your fi re.
As FPI does not have any control on quality or even the type of fuel mar-
keted, they assume no responsibility from any faulty operation related to
the type of fuel employed.
To Stop Stove
NOTE: The unit will take 120 minutes to shutdown completely.
1) Press the “Stop” button on the control panel.
2) The screen display will show Shut Down.