Four winns 338 Vista, Руководство пользователя

Страница: 67 / 161

Section H
Page 3
348 Vista Owner’s Manual
08/01
To prevent electrical problems, use only replace-
ment fuses or breakers that are of equal rating to
the originals.
Accessories - Accessory equipment that is customer or
dealer installed. These circuits are wired to a circuit
breaker in the 348. For additional information on adding
accessories, refer to Section H-4B.
Aft Bilge Pump - The BILGE PUMP switch is used to
manually activate the bilge pump in the engine compart-
ment. The bilge pump is used to remove water from the
bilge (bottom of the hull) area of the boat by pumping that
water overboard. The aft bilge pump is equipped with an
automatic bilge switch and will operate whenever bilge
water rises to a level that will cause the float to move
upward.
This automatic bilge pump is active even if the battery
selector switch is in the OFF position or if no battery
selector switch is installed. The automatic bilge pump
circuitry is connected directly to the batteries. When
leaving your boat unattended for an extended period,
check the charge on the battery(s) periodically. Also check
the water level in the bilge and make sure the float switch
is functional.
If the automatic bilge pump must be disabled, discon-
nect the wiring plug near the bilge pump.
Blower - The BLOWER switch is used to activate the
bilge blower. The bilge blower is used to remove any gas
vapors that may have accumulated in the bilge or engine
areas.
Gasoline vapors can explode resulting in injury
or death. Before starting the engine, check
engine compartment bilge for gasoline or vapors.
Operate blower for four minutes, and verify blower
operation. ALWAYS run the blower when the
vessel is operating below cruising speed.
Cockpit Lights - The CKPT LTS switch is used to activate
the cockpit (courtesy) lights.
Horn - To sound the horn, press the HORN switch.
Instrument Lights - On the 348, the INST LTS switch is
used to activate the instrument lights on the dash. It has
a two position switch that provides bright and dim lights.
Navigation & Anchor Lights - Moving the NAV/ANC LTS
switch towards the NAV position activates the bow lights
and the all-around light (or arch light if installed). Move
the switch to the ANC position to activate the all-around
light or arch light. The center switch position is OFF.
Trim Tabs - The boat is equipped with electric-hydraulic
trim tabs, the trim tabs are controlled by the TRIM TAB
switches. Refer to Section E-8 Trim Tabs for more infor-
mation.
Windlass - The WINDLASS switch activates the wind-
lass. Refer to the Section M-12 in this manual and the
manufacturer’s literature for additional information.
Stbd Wiper - The STBD WIPER switch activates the stbd
windshield wiper. The wiper will self park to the stbd.
Port Wiper - The PORT WIPER switch activates the port
windshield wiper. The wiper will self park to the stbd.
B. Installation of Additional 12 Volt Equipment
Accessories may be added to the boat by wiring directly
to the cabin panel. Non-factory installed 12 volt acces-
sory equipment can be connected to the “ACC” switch
on the dash.
Be sure to provide proper fuse or circuit breaker
protection for all 12 volt equipment that is installed.
DO NOT overload the accessory circuitry by in-
stalling too much additional 12 volt equipment.
C. Interior Equipment
Cabin equipment will be protected by the 12 volt DC cabin
panel on the 348 Vista. Cabin equipment information is
listed as follows:
CO Monitor - The CO monitors are protected by a circuit
breaker in the cabin panel.
Cabin Lights - To turn the overhead lights on, activate the
LIGHTING circuit breaker on the 12 volt cabin panel on
the 348. Use the corresponding switch panels or ON/
OFF switch located on mid cabin lights to activate.