FORTEZA TRIBO-M Скачать руководство пользователя

Страница: 6 / 52

JSC FORTEZA FORTEZA TRIBO-M

Please visit our internet sites:

www.forteza.com

www.forteza.eu

Page 6

Power source 9-36 V (DC);

With voltage drop below 5 V the guard alarm goes into the “Alarm” mod. ;

Current consumption < 100 mA;

Operating temperature from -40 °C to +50 °C;

Alarm, tamper output dry relay contact;

The duration of alarm signal is 1 s, minimum;

Fixed resistor value to control integrity of sensitive and non-sensitive elements;

Fixing on the metal fence with plastic ties on wooden with metal fix in elements (contact Forteza);

Compatibility any alarm control panel;

IP class IP55;

Equipment set up using computer;

Integral remote control of the detector. Suitable for any monitoring and control system;

1.4. Standard equipment

The following equipment is included in the guard alarm delivery set:

Signal-processing unit;

CD with Software Manual

Warranty

Optional: end sleeve, connection sleeve, USB/RS485 converter, sensitive element, non-sensitive

element, plastic ties can be included in the delivery set on the customer request.

The number of connection sleeves and couplings and the sensitive element length are to be agreed in

ordering.

Содержание TRIBO-M





















































Результаты поиска

Содержание TRIBO-M

Отзывы:

Похожие инструкции для TRIBO-M

Бренды по названию

Популярные бренды

FORTEZA TRIBO-M, Руководство по эксплуатации и установке

Результаты поиска

Содержание TRIBO-M

Отзывы:

Похожие инструкции для TRIBO-M

Бренды по названию

Популярные бренды