background image

Installation and operation instructions 

HOBS

8

ELECTRICALLY-IGNITED  

GAS BURNERS

These gas burners do not have Position 4, as 

shown in Figure 3.

To ignite a gas burner, press the 

selected gas burner control knob, 

turn it counterclockwise to the positi-
on of the symbol “Max. flame”   that 

corresponds to maximum gas supply.

Do not try to turn the knob without 

pressing it for this may result in damage 

to the gas valve. 

To ensure stable gas inflammation, press 

and hold the control knob within 3 seconds 

approximately. The inflammation process is 

attended by typical clicks caused by electric 

discharges within the igniters (Pos. 3, Figure 

3). Upon gas inflammation, select any posi-

tion of the control knob between symbols 
“Max. flame”   and “Min. flame”   to have a 

flame of desired intensity. If you have failed to 

ignite the gas burner, try it again proceeding 

in the same way. 

If the igniter is contaminated, electrical igni-

tion may not function properly. Therefore, it 

is highly recommended to keep the hob as 

clean as possible. Use a small brush to clean 

the igniter, as it may be required. Please bear 

in mind that it is not at all necessary to apply 

much force for cleaning. If, for some reason 

or other, electric power is not supplied or 

is cut off, you can ignite the gas burner the 

old-fashioned way – just lighting and setting 

a match. For that, press the control knob of 

the selected gas burner, turn it countercloc-
kwise up to the position “Max. flame”  . 

To turn off gas supply, rotate the control knob 
to the right, up to the position 

 “Flame OFF” 

(See Figure 2). 

ATTENTION! Electrical ignition process 

shall not last longer than 15 sec. 

If you have failed to ignite the gas burner 

after this time, or the flame has acciden-

tally extinguished, wait a minute prior to 

trying again. 

If you have failed to ignite the gas burner 

upon several attempts, please check the 

position of the gas burner cap (Pos. 1, Fi-

gure 3) and flame spreader (Pos. 2, Figure 

3).  

Pay attention to the following:

If the gas pressure of the gas supply network 

of your location is above the standard one, it 

will be easier to ignite the gas burner with a 

lesser volume of gas to be supplied. In this 

connection we recommend you to ignite the 

gas burner prior to putting the dishware onto 

the hob. We also recommend you to select 

the control knob position between “Max. fla-
me”   and “Min. flame”   or bring it to the 

“Min. flame”   position.

Содержание PGA 45 FIERO BL

























Отзывы: